the12volt's Members' Downloads: relay

Tech tip: The OEM gray/black door switch wire will not always work on some alarm installs for a door trigger due to a factory diode. The attached file shows how to obtain a clean ground and +12V feed on a 1995 F-Body (Camaro/Firebird) using two 5-pin relays. In 1996+, the function was handled by a body control module so this would not apply. This should work on 1993-95 cars. ...(Door_trigger_Dual_SPDT.pdf)

Tech tip: Adding relay to Ignition 2 (-) output of remote start to Igniton 2 of vehicle. ...(ign9596GMtrucks.gif)

Possible diagram for door locks on 2004 Dodge Ram 2500 remote start ...(remote start.jpg)

Engine compartment and interior fuse/relay center. Fuse descriptions only. ...(2011 Jetta TDI Fuse 03.pdf)

Module with two built in relays used for doorlocks or other uses. ...(EVS_451M_WebIns_03B_up.pdf)

...(EVS_451M_WebIns_8E_up.pdf)

Multiple relay wiring diagrams for devices and accessories. ...(RelayWireDigrams.pdf)

Bosche / Tyco relay catalog ...(ENG_DS_V23134-X0000-A001_F.pdf)

I have seen several requests for the above manuals, these are all the same alarm system just private labeled for each company. There is one slight difference in available remotes with the Command FM-760, a hands free remote p/n: TX040S. I emailed Commando asking of the price, availability and whether or not the base unit (brain) had the support circuitry already incorporated, their response: "TX040S is not available at this time". Since there is only one reference to this remote in the installation manual and since this manual is virtually identical to the AutoPage RS750LCD unit, with a little additional information and example relay circuits I suspect it is just a better Chinese to English translation. So for all intents and purposes the three units listed in the subject line are identical, from an installation and user point of view. I suspect that there will almost certainly have to be an ancillary unit that comes with the hands free TX040S remote, and that will interface with the base brain unit. zach_2 ...(FM-760install.pdf)

I have seen several requests for the above manuals, these are all the same alarm system just private labeled for each company. There is one slight difference in available remotes with the Command FM-760, a hands free remote p/n: TX040S. I emailed Commando asking of the price, availability and whether or not the base unit (brain) had the support circuitry already incorporated, their response: "TX040S is not available at this time". Since there is only one reference to this remote in the installation manual and since this manual is virtually identical to the AutoPage RS750LCD unit, with a little additional information and example relay circuits I suspect it is just a better Chinese to English translation. So for all intents and purposes the three units listed in the subject line are identical, from an installation and user point of view. I suspect that there will almost certainly have to be an ancillary unit that comes with the hands free TX040S remote, and that will interface with the base brain unit. zach_2 ...(FM-760owners.pdf)

Isolating ignition during remote starts. Accessory/Ignition/Starter Wire Isolation. When installing a remote starter into certain vehicles, you may experience the starter motor grinding excessively either during the key-takeover procedure or during the entire remote start process. This is typically caused by two or more wires that share a common contact at the key cylinder at rest, in a particular position (accessory position only, etc.), or during a mid-point between two positions. The solution for this symptom is usually to isolate the one (or more) of the circuits that have a common contact point by using a relay or by using the builtin Flex Relay found in most Directed remote starters (be sure to program Flex Output accordingly!). Known vehicles to require this doc include but are not limited to: 1993-1997 Nissan Altima, 1999-2006 Toyota Celica, 1999-2005 Toyota Echo and 2010+ Kia Soul. ...(1077.pdf)

Internal wiring diagram of Viper 5706v Remote Start relays ...(Viper5706Relays.JPG)

Tech tip: RAP Shutdown w/ DTIMAZDA When using the DTIMAZDA on a vehicle with retained accessory power, an additional relay must be used to open the driver’s door trigger on remote start shut down in order to shut down the retained accessory power circuit. The relay MUST be placed between the DTIMAZDA and the BCM as shown below in order to prevent the aftermarket security system from triggering. ...(DTI Mazda RAP shutdown.pdf)

How to install two batteries with the PAC80 40AMP Relay ...(Pac-80 Isolator-Relay instructions.pdf)

Tech tip: Ford PATS bypass with one relay and programmed key. This can be used for PATSI, PATS II and E-PATS ...(Ford_PATS_Bypass.pdf)

RAP Shutdown w/ DTIMAZDA When using the DTIMAZDA on a vehicle with retained accessory power, an additional relay must be used to open the driver’s door trigger on remote start shut down in order to shut down the retained accessory power circuit. The relay MUST be placed between the DTIMAZDA and the BCM as shown below in order to prevent the aftermarket security system from triggering. ...(1797.pdf)

Tech tip: Negative Trigger Priority Unlock with relay ...(NEG%20TRIG%20WITH%20PRIORITY%20UNLOCK.PDF)

Tech tip: Nissan Second Starter Relay Diagram ...(Second_Starter_Relay.pdf)

Tech tip: How to bypass the Passlock II anti-theft system with 2 relays. ...(Passloack_II.gif)

Tech tip: Add priority door locks to a system that does not have this option with the use of 3 relays. ...(DOUBLE_PULSE_DOOR_SYSTEM.gif)

Relay diagram for power windows. ...(Untitled.gif)

Tech tip: Shows how to do lock / unlock using a single channel from security system. This circuit uses three relays and be warned that it consumes current once the circuit is latched. Output labled FIRST should be used for lock whereas SECOND for unlock. ...(SingleWireLatchOnOff.jpg)

Tech tip: Please see the following forum topic: .../installbay/forum_posts.asp?TID=90057&PN=0&TPN=1 ...(FactTrans(1).pdf)