the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2012 jeep dball2, avital 4103 no power


Post ReplyPost New Topic
< Prev Topic Next Topic >
ziggyb222 
Silver - Posts: 593
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: January 04, 2004
Location: Maine, United States
Posted: February 04, 2014 at 9:48 AM / IP Logged  
You also need the BLACK/ white wire connected to either the toggle switch or directly to ground...
bpo118 
Member - Posts: 6
Member spacespace
Joined: January 31, 2014
Location: New Jersey, United States
Posted: February 04, 2014 at 9:53 AM / IP Logged  

You guys are awesome! Thank you for the quick replies.  I ended up getting everything working!! 

I think it was a faulty ground causing the issue.  I re did all my ground wires with a new grounding point and then everything worked.  After I got the Avital power it was a so easy after that.

Thanks again!!

joeeey 
Member - Posts: 17
Member spacespace
Joined: May 31, 2009
Location: New York, United States
Posted: October 26, 2014 at 4:42 PM / IP Logged  

I am having the same issue as the OP. 4X03 module , DBALL2 installing in a 06 Madza 3. When R/S is attempted ignition turns on but not cranking. I believe I am stuck in the D2D mode. I ground the white /blue completely disconnect unit, leaving the white /bue grounded when I power up I get nothing on the LED. But yet if I enter programming to learn the remotes the LED works. I also tried this on a bench powering up Ign pink, 12+ red, grounding black and black /white and I still get no LED to switch modes? I also tried this on 2 units and the same results. Leads me to beileive  DEI has a problem with their programing directions.

catback 
Silver - Posts: 703
Silver spacespace
Joined: August 13, 2002
Location: Canada
Posted: October 26, 2014 at 10:37 PM / IP Logged  
joeeey wrote:
I believe I am stuck in the D2D mode. I ground the white /blue completely disconnect unit, leaving the white /bue grounded when I power up I get nothing on the LED. But yet if I enter programming to learn the remotes the LED works...I also tried this on 2 units and the same results. Leads me to beileive  DEI has a problem with their programing directions.</SPAN>

Default mode is ESP so it's hard to be stuck in D2D - simply powering the unit with the WHITE/ blue not connected gives you ESP mode.
Depending on when the unit was made, instructions for the ESP/D2D port vary. I know of three different instructions on how to switch the ESP/D2D port mode.
Page of 2

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer