the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

avital 4x03 remote start, 98 lexus gs400


Post ReplyPost New Topic
< Prev Topic Next Topic >
kastenbm 
Member - Posts: 19
Member spacespace
Joined: March 18, 2014
Location: South Carolina, United States
Posted: March 18, 2014 at 12:09 PM / IP Logged  
Im new to this forum, so to anyone reading any help would be greatly appreciated!
I installed the avital remote start system in my 98 lexus gs400. The avital box an manual say model 4113 an the module says 4x03. Got everything hooked up an I can't get it to do anything...remote start will not program, status light will not come on at all, parking lights not flashing, etc. Everything is properly connected to best of my knowledge. Any ideas, thoughts, advice would be appreciated! Thanks
ccaudio 
Copper - Posts: 52
Copper spacespace
Joined: December 11, 2002
Location: Pennsylvania, United States
Posted: March 18, 2014 at 1:29 PM / IP Logged  
You have to make sure the antenna is plugged in for anything to work. Or I would check all my connections again
kastenbm 
Member - Posts: 19
Member spacespace
Joined: March 18, 2014
Location: South Carolina, United States
Posted: March 18, 2014 at 1:34 PM / IP Logged  
It definitely is plugged in. I also tried a different ground just to be sure, that didn't change anything. I'll triple check my connections though to make sure they're correct.
chev104275 
Gold - Posts: 1,419
Gold spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: November 26, 2007
Location: Massachusetts, United States
Posted: March 18, 2014 at 2:22 PM / IP Logged  
Can you list out your connections for us please
If i Can't Install it    I Don't need it   Joe
blanx218 
Silver - Posts: 654
Silver spacespace
Joined: September 23, 2008
Location: Pennsylvania, United States
Posted: March 18, 2014 at 3:29 PM / IP Logged  
Tap the WHITE/ blue wire to ground. If the car starts then it's a remote/antenna issue. If it doesn't then you have a power/ground issue or a defective brain.
kastenbm 
Member - Posts: 19
Member spacespace
Joined: March 18, 2014
Location: South Carolina, United States
Posted: March 18, 2014 at 3:54 PM / IP Logged  
Connections made:
     Module | Car
(-) Lights< >yellow/red
(Output) IGN< >BLACK / YELLOW
(Output) STA< >black
(Output) ACC< >blue / YELLOW
(Input) 12v < >WHITE/ blue
Program (Output)
for IGN/ACC < >BLACK/ white
        Tach< >BLACK / YELLOW(eng.bay ECM)
   (+) Brake< >GREEN / WHITE
*hood pinswitch shutdown connected
*Ground connected with bolt on crash bar under dash
chev104275 
Gold - Posts: 1,419
Gold spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: November 26, 2007
Location: Massachusetts, United States
Posted: March 18, 2014 at 3:56 PM / IP Logged  
Try what bland suggested
Where did you connect the BLACK/ white neutral safety shutdown wire ?
If i Can't Install it    I Don't need it   Joe
kastenbm 
Member - Posts: 19
Member spacespace
Joined: March 18, 2014
Location: South Carolina, United States
Posted: March 18, 2014 at 4:00 PM / IP Logged  
I don't currently have that switch connected. I was told it wasn't necessary since my hood pinswitch shutdown wire was connected. Wasn't sure if it was a must have?
chev104275 
Gold - Posts: 1,419
Gold spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: November 26, 2007
Location: Massachusetts, United States
Posted: March 18, 2014 at 4:07 PM / IP Logged  
The switch isn't but the wire is. If it's an automatic it should grounded. If it's a stick it needs to be connected to the ebrake.
If i Can't Install it    I Don't need it   Joe
kastenbm 
Member - Posts: 19
Member spacespace
Joined: March 18, 2014
Location: South Carolina, United States
Posted: March 18, 2014 at 4:35 PM / IP Logged  
I wired the neutral safety switch wire to ground (without the toggle switch), still nothing. I tried touching the WHITE/ blue activation wire to ground, nothing happened there either.
Page of 4

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer