viper 5704v on a 01 honda civic

i have a 01 honda civic ex and i am trying to install a viper 5704v remote start. i have the alarm working except the parking lights and the remote start. this is what iv done so far...any help will sure be appreciated... thanks 6pin connector h1/1 red to 12v white@ign h1/2 black to chassis ground h1/3 brown to siren(+) h1/4 WHITE/ brown didn't use h1/5 white to RED / black @ back of fuse box h1/6 orange didn't use door lock 3pin 1 blue to WHITE/ green 2 empty 3 green to WHITE/ blue 24 pin connector 1-8 didn't use 9 gray to hood pin (haven't connected yet 10 blue to RED / 2 sil. dots 11 didn't use 12 violet/white haven't connected yet to tach 13 BLACK/ white to chassis ground 14 did't use 15 green to green drivers door & lt.GREEN/ red passenger door &GREEN / WHITE both rear doors 16 BROWN / black to ORANGE / 2 sil. dots 17-19 didn't use 20 brown to WHITE/ black brake pedal 21-24 didn't use remote start 10 pin h3/1 pink to BLACK / YELLOW ign. h3/2 RED / white to BLACK/ red ign. h3/3 orange to WHITE/ red acc. h3/4 violet to BLACK/ white starter going to car side h3/5 green to BLACK/ white starter going to key side h3/6 red to white 12v @ign. h3/7 pink/white to BLACK/ red ign. h3/8 didn't use h3/9 RED / black to WHITE/ red acc. h3/10 not used

i connected the h1/5 white wire (parking light output) first to the blue wire parking ligh(-)located on the ign. switch harness and didn't work then a connected it to the RED / black wire(+) in harness clip next to the fuse box and it still doesn't work. please help. also the remote start doesn't do anything all i here is the alarm brain flixer like six times and the alarm remote say remote start error...

H3/RED / white to white constant please. Did you insert then change the polarity control 10amp fuse in the alarm brain, i.e. set NEG (-) to blue wire or set POS (+) to RED / black?Test before boxing up.

no i just changed the h1/5 white wire and tried it on the blue first and then the RED / black and nothing..

i did the fuse on the brain and it work the parking lights now work with the alarm. thanks. i also connected the H3/RED / white wire to white constant and still the same i get remote start error on the remote and the lights flicker 7 times. desperately need help. thanks

Seven Blinks = Manual Transmission Mode

If your Civic has an automatic transmission, program the Viper to Auto Trans - Menu 3, Item 1, Option 2.

You listed H2/2 BLACK/ WHITE (-) NEUTRAL SAFETY INPUT as not used.  It should be connected as follows :

With Auto Trans = Chassis Ground

With Manual Trans = Parking Brake (-)

Soldering is fun!

I have to say both of your problems are RTFM linked. Does this vehicle have an immobiliser?

thanks kreg357 it work. it remote started with the key in the ign. i also connected this to 12v constant h3/2 h3/6 h3/9 now i can connect the 555i. is there a diagram or something showing how to connect this. where i can find a diagram to find which wires are located on my car. thanks u guys for all ur help....

Yes in the box that the 555i came in, again all related to RTFM. Please read the last line on my signature.

Here is a link to the 555i install guide, in case yours' is lost.  https://www.the12volt.com/installbay/file.asp?ID=1269

As for the Civic's wires, here is some info from iDatalink :

Ignition ~ ~     Pin 6 Yellow/Black (+)   @ Ignition switch transponder plugData ~ ~         Pin 2  RED / Blue (DATA)         @ Ignition switch transponder plug

Keysense info from ReadyRemote :

Keysense       RED / white (-)    @ factory alarm plug above driver kick, green 16 pin plug, pin 12

The 555i Blue R/S Input wire connects to the Viper 5704 Dark Blue (-)  200mA Status Output.

Soldering is fun!