passat b6 with viper5704 and dball2

hello everyone, I'm new from here... I have an automatic VW Passat B6 2010 model, and I want to install a security car sistem with remote start with DBALL2. I have following modules: -Viper 5704 -Directed 556U-B / 556UW for transponder key -XpressKit XpressKit DBALL2 for CAN comunicatin -Directed Directed 620V led flash -Directed Directed 507M till sensor -Directed Directed 506T audio sensor I connected Viper 5704 to DBALL2 via W2W see diagram, but I have issues with connecting the Remote Start wires...could you help me with these? Ovidiu

I don't use the heavy gauge wiring, I substitute thinner stuff. One of the easiest cars to do, wire it D2D. Just follow that diagram. I also believe you need a by-pass for OEM immobiliser look at the first few pages of the install guide.

now I have done W2W..how I can change to D2D..just unplug the conectors? plesea, could you help me with H3 connection harness? here is what I think, but correct me if I missed someting. remote start 10 pin heavy gauge connector       H3/1 pink (+) ignition 1 input/output     pin 11 black of G plug @BCM and pin 9 of 10 pin connector on dball2 H3/2 RED / white (+) fused 30a ignition 2/ flex replay input 87      pin 16 green of starter ignition harness H3/3 orange (+) accessory output      12V constant H3/4 violet (+) starter output car side of started kill      cut 3 GREEN/ red starter wire at ignition harness & connected H3/4 to starter side  H3/5 green (+) started input key side of starter kill      cut 3 GREEN/ red wire at ignition harness and connected H3/5 to key side  H3/6 red (+) fused 30a ignition 1 input      H3/7 pink/white (+) ignition 2 flex relay output      H3/8 pink/black (+) flex relay input 87a key side if required of flex relay      not used  H3/9 RED / black (+) fused 30a accessory/starter input      connected to same wire at ignition harness as I connected H3/2(RED / white)  Ovidiu

It looks like all your H3 wires are wrong, I'll get back to you later.

H3/1 Pink Correct. H3/2 RED / white not used. H3/3 Orange not used. H3/4 Violet to starter side after cutting RED / black starter wire. H3/5 Green to plug side of RED / black starter wire. H3/6 Red to thick plain red at fusebox, side of instrument panel. H3/7 Pink/white not used. H3/8 Pink/black not used. H3/9 RED / black join to red above. Now read page 4 of the install guide.

thanks a lot... I've read...and I connect: pin 2 blue from bypass module to: -H2/5 dark blue (-) 200mA Status Output (Viper 5704)     -pin 10 blue/white (-) GWR (status) input (DBALL2) isn't corect?Ovidiu

Yes, exactly as you said.

my DBALL2 module is unprog. and i don't have XLoader2, is it posible to program is without XKLoade2? regarding interconnection, I'll use W2W, and I have one wire which I dont no where I can connect it to alarm system (pin 8 (+) Start Input from black connector -- DBALL2)... If I connect cable for D2D...module switch automaticaly to D2D, or I need to unplug conector? thank you again Ovidiu

No. And I fail to understand the second part of your question, just follow the diagram.

in D2D mode it has more functions...and if I want to shich from W2W to D2D...how I can do this? when I connect cable whit 4 pins...module knows and shich automaticaly...to D2D? or it is necessary to unplug conectors from alarm system?! I hope to understand now (my English is not so good...:)) regarding sensors...how it is better to pair them first connector(shock sensor + till sensor) and the second connector (audio sensor)...isn't correct?Ovidiu