the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Viper 5706v, 2010 Hyundai Elantra


Post ReplyPost New Topic
< Prev Topic Next Topic >
catback 
Silver - Posts: 703
Silver spacespace
Joined: August 13, 2002
Location: Canada
Posted: August 25, 2014 at 8:24 AM / IP Logged  
wissam1981 wrote:
and what about the ( Diagnostic Connector OBD2 ) should i hooked up with the DBall2 ????
Didn't you say your car DOES NOT HAVE an OBD2 port?
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: August 25, 2014 at 8:28 AM / IP Logged  
CB No car built after 98 doesn't have an OBD port.
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: August 25, 2014 at 8:36 AM / IP Logged  
Cat back, please empty your PM inbox, been trying to PM you for two days!
catback 
Silver - Posts: 703
Silver spacespace
Joined: August 13, 2002
Location: Canada
Posted: August 25, 2014 at 8:36 AM / IP Logged  
Howie, just going by what the owner has said, no factory security and no OBD2 said the owner. On these parts, OBD2 has been around since '96 and is mandatory of auto manufacturers.
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: August 25, 2014 at 8:38 AM / IP Logged  
Under dash, left hand side and as I said before, body CAN wires also at BCM and driver;s door loom.
wissam1981 
Copper - Posts: 116
Copper spacespace
Joined: July 24, 2014
Location: Florida, United States
Posted: August 25, 2014 at 9:06 AM / IP Logged  
Guys, this is my final, i need a conformation
DBall2   To Viper
1- D2D cable
2- D10/9 pink (+) { ignition input } to H1/1 Red (+)12v constant input
3- tan/black HSCAN highto   OBD2
4- tan HSCAN low  to    OBD2
Viper to Car
1- H6/2 black (-) { Chassis Ground }to Ground ( Car Body )
2- H6/4 WHITE/ brown { parking light } to parking light (+)
3- H10/5 Red (+) fused 12v ignition 1 input     to 12v constant white (+)????????
4- H10/6 Green (+) starter input ( key side of the starter kill )        to starter white (+)
5- Red (+)12v constant input to 12v Black (+)
6- H10/8 Accessory output (+) orange to orange pin 3
7- H6/3 brown (+) siren output  to car siren
8- H10/2 RED / black (+) fused 12v acc. / starter input        to 12v constant
9- H10/5 red (+) fused 12v ignition 1 input       to 12v constant
10- H10/9 RED / white (+) fused 12v ignition 2 / flex relay input 87    to 12v constant
DBall2 to Car
1- D10/9 pink (+) ignition input       to ignition 1 blue (+)
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: August 25, 2014 at 9:31 AM / IP Logged  
I give up.
wissam1981 
Copper - Posts: 116
Copper spacespace
Joined: July 24, 2014
Location: Florida, United States
Posted: August 25, 2014 at 9:35 AM / IP Logged  
no no no no
you are my only hope, please
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: August 25, 2014 at 9:46 AM / IP Logged  
You will never finish this you've got half of the above wrong!
Why WHITE/ brown when it says white?
I've NEVER used the WHITE/ brown.
Pink at DB-ALL black plug to pink at H3 to blue at ignition switch.
H3 red,RED / white and RED / black to black at ignition switch OR main (+) battery feed at fuse box. Battery feed = 12V+ constant.
Cut white starter lead, H3 Green to key side H3 Purple to starter side.
Others are correct.
wissam1981 
Copper - Posts: 116
Copper spacespace
Joined: July 24, 2014
Location: Florida, United States
Posted: August 25, 2014 at 10:26 AM / IP Logged  
thank you, you didn't give up on me.
1- all the above make scene now , but i didn't get the last part ( Cut white starter lead, H3 Green to key side H3 Purple to starter side )
2- about the light flash polarity, which side should i put the fuse ??
Page of 22

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer