the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2014 prius c r start hybrid error


Post ReplyPost New Topic
< Prev Topic Next Topic >
kenca 
Member - Posts: 6
Member spacespace
Joined: August 31, 2014
Location: Manitoba, Canada
Posted: August 31, 2014 at 8:59 PM / IP Logged  
I installed a few diy remote starter with fortin evo all with success. This is my first time installing with idatalink blade al bypass module with firstech FT-6200S. I connected all the wires shown on type 10 for prius c 80 bit keys from http://www.idatalink.com/product/product/product_id/4 blade al tl5 installation guide and the blade seems to work properly based on the above guide. When I remote start the car it started and got the "ready" light but I get hybrid error. I bought the cable to reflash the blade module but same problem.
tonanzith 
Gold - Posts: 593
Gold spaceThis member consistently provides reliable informationspace
Joined: July 18, 2008
Location: Washington, United States
Posted: August 31, 2014 at 9:19 PM / IP Logged  
Does it light up also during regular start or only on remote start?
Gary Sather
kenca 
Member - Posts: 6
Member spacespace
Joined: August 31, 2014
Location: Manitoba, Canada
Posted: September 01, 2014 at 9:37 AM / IP Logged  
only on remote start.
catback 
Silver - Posts: 703
Silver spacespace
Joined: August 13, 2002
Location: Canada
Posted: September 01, 2014 at 11:56 AM / IP Logged  
You have all (except keysense) the ignition connector wires hooked up (12V, Ign A, Ign B, Acc, Starter)?
Where are you taking power for the FT-6200S from? I wouldn't use the 12V wire at the ignition connector for anything other than powering the remote start harness that feeds the ignition connector.
kenca 
Member - Posts: 6
Member spacespace
Joined: August 31, 2014
Location: Manitoba, Canada
Posted: September 01, 2014 at 9:44 PM / IP Logged  
yes 12v, ground, ign, acc, starter, -parking. On the blade I connected the canH, canL, Immobilizer data, ground, doorlock data, and -ground input hook up to ground when running on the FT-6200S. No I didn't connect keysense, the guide said not to connect it. I used the 2 back 12v wires from the ignition to power the two red 12v on the FT-6200S.
catback 
Silver - Posts: 703
Silver spacespace
Joined: August 13, 2002
Location: Canada
Posted: September 02, 2014 at 10:09 AM / IP Logged  
There are two ignition wires A and B, they both have to be connected. Also recommended place to grab 12v is at the fuse box, the idatalink guide says the given black 12v wire at the ignition connector only supports 7.5 amps.
kenca 
Member - Posts: 6
Member spacespace
Joined: August 31, 2014
Location: Manitoba, Canada
Posted: September 02, 2014 at 8:49 PM / IP Logged  
Problem solved thank you. I didn't connect ignition B.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer