the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2014 fusion locks and dball2


Post ReplyPost New Topic
< Prev Topic Next Topic >
nitrous1 
Member - Posts: 2
Member spacespace
Joined: November 27, 2006
Location: United States
Posted: October 15, 2014 at 5:39 PM / IP Logged  
I'm in the process of installing a Viper 5704 RS/alarm with a DBALL2 interface (D2D) in my 2014 Ford Fusion Hybrid (no Smart Key). I uploaded the latest firmware for my car (402.FORD10 v1.12) into the module using my XKLoader. I went through the module programming instructions provided by XpressKit.com and I am having trouble getting the door locks to work. The car seems to recognize the DBALL2 unit as another transponder key because I get a "Key Programmed Successfully" message on my dash and the door locks cycle once just like they are supposed to for the normal Ford PATS system programming routine. The car will remote start just fine but the lock/unlock buttons on the Viper remote do not lock/unlock the doors. Strangely enough, the power trunk will release using the Viper remote and the interface will properly sense the Hood Pin status through the CAN bus. Any idea what I'm doing wrong? I've installed a few other RS/alarm units on my vehicles over the years so this isn't my first install. I always seem to have trouble getting an interface module to properly control the door locks so it must be something I'm doing. When I did my 2004 Corvette and 2013 Hyundai Elantra GT, I ended up hard wiring the door locks to make them work but there has to be a better way.
Thanks in advance!
tonanzith 
Gold - Posts: 593
Gold spaceThis member consistently provides reliable informationspace
Joined: July 18, 2008
Location: Washington, United States
Posted: October 15, 2014 at 9:00 PM / IP Logged  
Did you flash the module foe d2d?
Gary Sather
racerjames76 
Silver - Posts: 581
Silver spacespace
Joined: November 22, 2008
Location: Ohio, United States
Posted: October 16, 2014 at 9:57 AM / IP Logged  
Contact DEI directly. There are a few custom firmwares available for that car.
To master and control electricity is perfection. *evil laugh*
nitrous1 
Member - Posts: 2
Member spacespace
Joined: November 27, 2006
Location: United States
Posted: October 22, 2014 at 11:07 AM / IP Logged  
I played around with the various D2D settings and re-flashed the unit several times. I never was able to get the locks to work through the DBALL2. I ended up hard wiring them to the Viper R/S unit. It was a real pain to run the wires through the factory boot and connectors but I made it work.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer