the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

viper alarm 5704v into 96 integra


Post ReplyPost New Topic
< Prev Topic Next Topic >
slammedcx 
Member - Posts: 2
Member spacespace
Joined: October 24, 2014
Location: California, United States
Posted: October 24, 2014 at 11:50 AM / IP Logged  
I have a viper alarm 5704v and im trying to install it into my 96 integra. I got the basic power ground and siren hooked up as well as the locks, now im having issues wiring up these,
h1/4 white w/brown parking light isolation wire? were does this go?
h1/5 white parking light output were does this go?
h1/6 orange (-)500mA ground when armed output, were does this go?
then also I attempted to wire up the remote start but on this alarm I got the heavy gauge 10 pin connector wire up but when I plug into the brain the alarm does arm or disarm or anything, but I also am having questions on were to wire up the 24 pin connector, I know like half of them aren't gonna be used here's a list of ones I need help with
h2/1 pink w/white- (-)200mA ignition/flex relay control output
h2/2 BLACK/ white (-) neutral safety input
h2/6 green (-) door trigger input (n/c or n/o)
h2/7 BLACK / YELLOW (-)200mA domelight supervision output
h2/9 dark blue (-)200mA status output
h2/10 pink (-)200mA ignition1 output
h2/12 (+) door trigger input
h2/16 brown (+)brake shutdown input
h2/18 violet / YELLOW (-)200mA starter output
h2/21 WHITE/ blue (-) remote start/turbotimer activation input
h2/22 orange (-)200mA accessory output
any help is very appreciated thanks
racerjames76 
Silver - Posts: 581
Silver spacespace
Joined: November 22, 2008
Location: Ohio, United States
Posted: October 25, 2014 at 8:24 AM / IP Logged  

I wil help with what I can.

slammedcx wrote:
I have a viper alarm 5704v and im trying to install it into my 96 integra. I got the basic power ground and siren hooked up as well as the locks, now im having issues wiring up these,
h1/4 white w/brown parking light isolation wire? were does this go? Not needed for you application
h1/5 white parking light output were does this go? This is the parking light output and will hook to the wire that tests as either power 12v +ve when turning the parking lights on, or ground -ve when turning the parking lights on with the head light switch.
h1/6 orange (-)500mA ground when armed output, were does this go? This wire would control a start kill relay if you install one. Personal opinion is you do not need a starter kill relay but we can help if you wish to do it.
then also I attempted to wire up the remote start but on this alarm I got the heavy gauge 10 pin connector wire up but when I plug into the brain the alarm does arm or disarm or anything, but I also am having questions on were to wire up the 24 pin connector, I know like half of them aren't gonna be used here's a list of ones I need help with
h2/1 pink w/white- (-)200mA ignition/flex relay control output Should not be needed
h2/2 BLACK/ white (-) neutral safety input  Must be hooked to ground or ebrake (manual transmission) in order for the remote start to operate
h2/6 green (-) door trigger input (n/c or n/o) Connect to a negative door pin or domelight circuit. Also required on manual transmission. May need diodes for multiple door pins.
h2/7 BLACK / YELLOW (-)200mA domelight supervision output Hook to a door pin or domelight wire to allow for the domelight to turn on when you press unlock. For +ve domelight circuits or high current ground needs you will need to use a relay.
h2/9 dark blue (-)200mA status output  Can be used for either a bypass (interface) or defrost turn on
h2/10 pink (-)200mA ignition1 output  Should not be needed
h2/12 (+) door trigger input
h2/16 brown (+)brake shutdown input  Required for remote start shut down. Will attach to a wire that tests 12v +ve when the brake pedal is pressed.
h2/18 violet / YELLOW (-)200mA starter output Should not be needed
h2/21 WHITE/ blue (-) remote start/turbotimer activation input  Should not be needed
h2/22 orange (-)200mA accessory output  Should not be needed
any help is very appreciated thanks

To master and control electricity is perfection. *evil laugh*
slammedcx 
Member - Posts: 2
Member spacespace
Joined: October 24, 2014
Location: California, United States
Posted: October 25, 2014 at 12:56 PM / IP Logged  
thanks very much I really appreciate it ima give it a shot!!
catback 
Silver - Posts: 703
Silver spacespace
Joined: August 13, 2002
Location: Canada
Posted: October 25, 2014 at 5:54 PM / IP Logged  
Starter Kill/Anti-grind is built-in to the 5704v so it only needs to be correctly wired up, an external relay is not required.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer