the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

python 4211p with immobilizer bypass wire


Post ReplyPost New Topic
< Prev Topic Next Topic >
lopezchris21 
Member - Posts: 21
Member spacespace
Joined: May 24, 2010
Location: Florida, United States
Posted: October 31, 2014 at 9:50 PM / IP Logged  
Hello guys. I would like some confirmation on my wires before i jump into this. If anyone sees anything wrong please let me know. Also if there is a question mark next to it im not sure about it.
Thank you
Remote start - python 4211p with Dball2pro with XCRS (extreme capacity relay satellite)
Car - 2006 honda civic si
16 pin connector
pin 3 Immobilizer Data: ORANGE / Black to pin 3 on immobilizer plug
pin 6 single wire can Lt. green to pin 4 on immobilizer plug
pin 10 (-) lock output GREEN/ black to Pin 28 driver side kick panel (34 pin plug)
pin 13 (-) unlock output Lt. Blue/ black to Pin 27 driver side kick panel (34 pin plug)
XCRS plug
Violet + Starter output (starter side) to Cut yellow in half at ignition switch starter side
Green starter input (from key) to Cut yellow in half at ignition switch Key side
Red + 12 v input to BLue + Ignition switch
Orange Accessory output + to Orange + Igniton Switch
Red +12v input to BLue + Ignition switch
Pink + Ignition Output (also input to yellow wire in ribbon) to ???
RED / wht + Fused 30a ignition 2/ Flex relay input to NOT USED
Pink/ wht +ignition 2 / Flex relay output to NOT USED
18 pin connector
Pin 3 gray Hood input - to Hood pin on bay
Pin 8 BROWN / blk Horn - to Orange Fuse box rear 16 pin plug
pin 13 lt blue trunk input - to ??? Trunk release is green but + kick panel 42 pin plug
Pin 17 brown siren output + to NOT USED
12 pin connector
pin 1 &7 white Parking light output + to ???
Pin 2 &8 white / brown Parking light input + to ???
pin 9 black Ground - to Body
pin 10 red 12V + to BLue + Ignition switch
If i am missing anything please let me know.
Thanks
lopezchris21 
Member - Posts: 21
Member spacespace
Joined: May 24, 2010
Location: Florida, United States
Posted: November 03, 2014 at 12:31 AM / IP Logged  
no one?
Where do the Flex wires go?
What about the light output/input?
Anything on Pink + Ignition Output (also input to yellow wire in ribbon) to ?.
Any help please
bs1d3 
Copper - Posts: 58
Copper spacespace
Joined: February 17, 2014
Location: United States
Posted: November 03, 2014 at 5:02 PM / IP Logged  
Red, Red and RED / White will all go to 12v (white) at the ignition switch.
Pink goes to ignition (blue) at the ignition switch.
Pink/White goes to 2nd ACC (red) at ignition switch. (Program to ACC in menu instead of IGN)
Trunk input is for an alarm or manual trans.
White will go to your + parking light wire (red @ fuse box, lt green plug pin 19)
WHITE/ brown goes to 12v (white) at ignition switch or tie it in to your other 12v wires.
lopezchris21 
Member - Posts: 21
Member spacespace
Joined: May 24, 2010
Location: Florida, United States
Posted: November 03, 2014 at 5:13 PM / IP Logged  
Thanks so much for your input. Question.
I want to trick it to think my car is auto. Will this wiring be the same?
Will I need the trunk when doing this?
Someone mentioned a neutral safety switch. Do I need that?
Thanks for your time.
lopezchris21 
Member - Posts: 21
Member spacespace
Joined: May 24, 2010
Location: Florida, United States
Posted: November 03, 2014 at 5:14 PM / IP Logged  
Also the very last red 12v on the pin 10, wood that also go to the white?
smokeman1 
Platinum - Posts: 1,588
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: September 14, 2009
Location: Wisconsin, United States
Posted: November 04, 2014 at 6:54 AM / IP Logged  
I want to trick it to think my car is auto.
Bad Move. If car is manual transmission.
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
lopezchris21 
Member - Posts: 21
Member spacespace
Joined: May 24, 2010
Location: Florida, United States
Posted: November 04, 2014 at 7:32 AM / IP Logged  
Why is it a bad move?
As long as im careful with not leaving it in gear, what can go wrong? I'm in and out of my car a lot and do not want to deal with the procedure of a manual.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer