avital 4301 not working

I had a viper 550 esp alarm and i uninstalled it and hooked up the 4103. every thing i needed is connected except the satalite relay ( read some where i didnt need this) and nothing is working, no sound when i hit the door locks or the remote start but when you hit the valet switch the light on the alarm does come on. i trtied to do the remote programing and started the key hit the button once let go hit again and pressed the lock key let go turned off key and didnt work also the horn didnt sound any ideas?

forgot to mention i have a 99 isuzu vehicross

can you list out your connections so we can get a better look at what's going onIf i Can't Install it    I Don't need it   Joe

ok hooked up on the 3 pin blue and greenshich are lock unlock 6 pin hooked up all wires high current 12v, output to second ignition,high current 12v, accessory circuit,starter circit, and primary ignition circuit on satellite harness nothing hooked up on remote start 5 pin hooked up neutral safety switch ,tachometer input, brake shutdown, did i miss something? should this come already programed? if not how do i program it? thanks

zadam123 wrote: ok hooked up on the 3 pin blue and greenshich are lock unlock 6 pin hooked up all wires high current 12v, output to second ignition,high current 12v, accessory circuit,starter circit, and primary ignition circuit on satellite harness nothing hooked up on remote start 5 pin hooked up neutral safety switch ,tachometer input, brake shutdown, did i miss something? should this come already programed? if not how do i program it? thanks

also on the 9 pin i hookied up horn and groun d and light flash output, which are brown, black and white

anyone????

Trying to follow what you have done but it's hard to read could you do something like this 4103.       Truck 6 pin connector Red. White Red. WHITE/ black Purple.      BLACK/ white Orange.    BlueIf i Can't Install it    I Don't need it   Joe

ok sorry 9 pin black - I grounded white - GREEN/ YELLOW brown - horn (dont remember color 3 pin blue - RED / black green - RED / white 6 pin red -white black pink/white - RED / black red - red white orange - blue purple - black white pink - black yellow 5 pin black white - dont remember have to look violet white - red black brown - red blue

Ok did you meter everything before you connected your wiring ? I've never done this particular truck but according to my diagrams some of your wires may be wrong but the diagrams could also be wrong. The BLACK/ white on the 5 pin harness needs to see ground for the truck to start. ISUZU VEHICROSS VEHICROSS      1999-2002 PART      COLOR      LOCATION      DIAGRAM 12 VOLT CONSTANT      WHITE (+) and WHITE/ BLACK (+)      IGNITION SWITCH HARNESS      STARTER      BLACK/ WHITE (+) or WHITE/ BLUE (+)      IGNITION SWITCH HARNESS            IGNITION 1      BLACK / YELLOW (+) or BLACK/ RED (+)      IGNITION SWITCH HARNESS      IGNITION 2      BLACK/ RED (+) or BLACK / YELLOW (+)      IGNITION SWITCH HARNESS      ACCESSORY /HEATER BLOWER 1      BLUE (+)      IGNITION SWITCH HARNESS              PARKING LIGHTS ( - )      YELLOW (-) or GREEN/ YELLOW (-)      @ HEADLIGHT SWITCH       PARKING LIGHTS ( + )      GREEN/ RED (+)      IN DRIVERS KICK PANEL       POWER LOCK      RED / WHITE (TYPE B)      IN DRIVERS DOOR HARNESS       POWER UNLOCK      RED / BLACK (TYPE B)      IN DRIVERS DOOR HARNESS       LOCK MOTOR WIRE      LIGHT GREEN (+)      IN DRIVERS DOOR HARNESS      DOOR TRIGGER      RED / GREEN (-)      IN PASSENGER KICK PANEL      DOMELIGHT SUPERVISION      USE DOOR TRIGGER, Requires Part #775 Relay       HORN      GREEN (-) or ORANGE / BLACK (-)      @ STEERING COLUMN HARNESS      TACH      BLACK/ RED      @ PCM, See NOTE *1            BRAKE      RED (+)      @ SWITCH ABOVE BRAKE PEDAL      NOTE *1 the PCM (Powertrain Control Module) is located in the CENTER CONSOLE. If i Can't Install it    I Don't need it   Joe