the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2005 Scion xB power locks


Post ReplyPost New Topic
< Prev Topic Next Topic >
leathur 
Member - Posts: 3
Member spacespace
Joined: February 22, 2005
Posted: March 06, 2005 at 12:12 AM / IP Logged  
Hello. I have installed a CrimeGuard 745i2 into my 2005 xB. This alarm used to be in my Integra, but i upgraded to a Viper 791. Anyway, the CrimeGuard is working fine on the xB except that i cannot get it to LOCK the doors when the alarm is armed. However, i was able to finally get it to UNLOCK when disarming.
I realize, on the Scions, the UNLOCK requires a double pulse (-) and the Crimeguard 745i2 only puts out a single unlock pulse. It has no option for a double pulse. (maybe the Crimeguard 745i4 has this option). After further research, i found out that i could tap into the UNLOCK wire (blue/red) on the passenger side kick panel instead, because it only requires a single pulse.
Does the brain need to send out a double pulse for it to LOCK? If so, then i guess im out of luck. I'm connecting to the LOCK wire (Blue/White) located in the drivers side kick panel, as suggested by the wiring guides i have seen. Any help would be appreciated. Thank you.
another-kelly 
Silver - Posts: 618
Silver spacespace
Joined: July 11, 2004
Location: United States
Posted: March 06, 2005 at 1:11 AM / IP Logged  
SCION / XB / 2005 / Remote Start
12volts wht/blue (40A), wht/red (15A)  +  ignition harness
Starter black  +  ignition harness
Second Starter N/A    
Ignition black  +  ignition harness
Second Ignition BLACK / YELLOW  +  ignition harness
Third Ignition N/A    
Accessory blue/red  +  ignition harness
Second Accessory N/A    
Keysense yellow  -  ignition harness
Power Lock blue/white  -  driver kick, 14 pin plug
Notes: Meter these wires while turning the key in the driver door key cylinder.
Power Unlock yellow/black (double pulse)  -  driver kick, 14 pin plug
Notes: Meter these wires while turning the key in the driver door key cylinder.
Can also use the passenger door key cylinder wire for unlock, which only requires a single pulse. It is blue/red (-) in the passenger kick in a 14 pin plug.
Lock Motor blue/orange  5wi driver kick, 9 pin plug
Unlock Motor YELLOW /GREEN  5wi driver kick, 9 pin plug
Parking Lights+ green  +  headlight switch
Notes: Also found at the top of the fuse box in a 13 pin plug.
Parking Lights- N/A    
Hazards GREEN/ orange  -  hazard switch
Turn Signal(L) GREEN/ black  +  top of fuse box, 13 pin plug
Turn Signal(R) GREEN/ YELLOW  +  top of fuse box, 13 pin plug
Reverse Light RED / black  +  top of fuse box, 9 pin plug
Door Trigger RED / white  -  top of fuse box, 9 pin plug
Dome Supervision use door trigger wire    
Trunk/Hatch Pin common with door trigger wire    
Hood Pin N/A    
Trunk/Hatch Release N/A    
Power Sliding Door N/A    
Factory Alarm Arm N/A    
Factory Alarm Disarm N/A    
Disarm No Unlock N/A    
Tachometer black  ac  data link conn below fuse box, pin 9
Wait to start N/A    
Brake Wire GREEN/ red  +  brake pedal switch
Notes: Also found at the top of the fuse box in a 13 pin plug.
Parking Brake black  -  parking brake switch
Horn Trigger WHITE/ red  -  steering column
Memory Seat 1 N/A    
Memory Seat 2 N/A    
Memory Seat 3 N/A    
2005 Scion xB power locks -- posted image.
Immobilizer Bypass Module:Required: NoType: N/APart #: N/A
Notes: N/A
another-kelly 
Silver - Posts: 618
Silver spacespace
Joined: July 11, 2004
Location: United States
Posted: March 06, 2005 at 1:12 AM / IP Logged  
thatsa whata i gotsa. hope ya can get to unlock
leathur 
Member - Posts: 3
Member spacespace
Joined: February 22, 2005
Posted: March 06, 2005 at 1:29 AM / IP Logged  
Thanks. That looks like the wiring guide i was using. I can get it to unlock, but i cannot get it to lock when i connect the lock wire from the brain to the blue/white wire on the 14 pin plug located in the drivers side kick panel
another-kelly 
Silver - Posts: 618
Silver spacespace
Joined: July 11, 2004
Location: United States
Posted: March 06, 2005 at 1:36 AM / IP Logged  
you using a DMM? disconnect your lock wire from the blue/white and check it for it's neg. locl pulse when you are. did you also meter the blue/white with a DMM per the wiring info?
leathur 
Member - Posts: 3
Member spacespace
Joined: February 22, 2005
Posted: March 06, 2005 at 8:10 PM / IP Logged  
i was about to meter the blue/white wire and then i remembered there were 2 violet wires on the door lock harness that were grounded when i had the alarm in my integra. so i grounded those 2 violet wires and everything's fine now. Thanks for your help!

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer