the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

G35 remote start


Post ReplyPost New Topic
< Prev Topic Next Topic >
rac0000 
Member - Posts: 4
Member spacespace
Joined: February 13, 2005
Location: United States
Posted: May 20, 2005 at 5:19 PM / IP Logged  
I have a 2005 infiniti g35x on order and want to install a remote start.You guys helped me out big time on a remote start for my 2003 accord. I need to know what i'll need to do the job right. (modules and bypass kits?). Also a wiring diagram and wire location would be very helpful.Also,if anyone knows of any snags i may run into in the installation.

                                                                                              Thanks

rac0000
Pearl96Max 
Member - Posts: 16
Member spacespace
Joined: July 21, 2002
Location: United States
Posted: May 20, 2005 at 10:51 PM / IP Logged  
Congrats on your purchase. I just picked one up lastweek as as well.
All youll need is a 556U Immobilizer Bypass.
Heres the tech sheet:
DIRECTWIRE™ WIRING INFORMATION - INFINITI / G35 SEDAN / 2005 / Remote Start
[PRINT THIS PAGE]
12volts WHITE/ blue (40A)   +   ignition harness
Starter WHITE/ red   +   ignition harness
Second Starter WHITE/ green   +   ignition harness
Ignition BLACK/ red   +   ignition harness
Second Ignition N/A       
Third Ignition N/A       
Accessory WHITE/ black   +   ignition harness
Second Accessory N/A       
Keysense BLACK/ pink   +   ignition harness or BCM, pin 37
Notes: The BCM (Body Control Module) is in the driver kick panel.
Power Lock RED / white   -   driver door module in door
Notes: Meter this wire while turning the key in the driver door key cylinder.
Power Unlock blue/white (double pulse)   -   driver door module in door
Notes: Meter this wire while turning the key in the driver door key cylinder.
Lock Motor purple   5wi BCM, pin 50
Notes: The BCM (Body Control Module) is in the driver kick panel.
Unlock Motor yellow   5wi BCM, pin 44
Notes: The BCM (Body Control Module) is in the driver kick panel.
Parking Lights+ RED / blue   +   driver kick, harness to rear
Parking Lights- N/A       
Hazards GREEN/ red   -   switch or BCM, pin 29
Notes: The BCM (Body Control Module) is in the driver kick panel.
Turn Signal(L) GREEN / WHITE   +   BCM, pin 45
Notes: The BCM (Body Control Module) is in the driver kick panel.
Turn Signal(R) PURPLE / white   +   BCM, pin 46
Notes: The BCM (Body Control Module) is in the driver kick panel.
Reverse Light red or orange   +   driver kick, harness to rear
Door Trigger white (D), pink (P)(x3)   -   BCM, pins 62, 12, 63 and 13
Notes: Use all four wires and diode isolate each.
The BCM (Body Control Module) is in the driver kick panel.
Dome Supervision PURPLE / red   -   BCM, pin 48
Notes: The BCM (Body Control Module) is in the driver kick panel.
The step lamps are yellow/purple (-) at the BCM, pin 47.
Trunk/Hatch Pin RED / white   -   BCM, pin 57
Notes: The BCM (Body Control Module) is in the driver kick panel.
Hood Pin lt. GREEN/ black   -   hood pin switch under hood
Trunk/Hatch Release pink or blue   -   BCM, pin 30
Notes: The BCM (Body Control Module) is in the driver kick panel.
The trunk release motor wire is GREEN / WHITE (+) at the BCM, pin 68.
Power Sliding Door N/A       
Factory Alarm Arm arms with lock       
Factory Alarm Disarm disarms with unlock       
Disarm No Unlock single pulse power unlock wire       
Tachometer NOT WHITE/ blue, red or black   ac   any ignition coil or fuel injector
Wait to start N/A       
Brake Wire pink/blue   +   brake pedal switch
Parking Brake RED / white or PURPLE / red   -   parking brake switch
Horn Trigger GREEN/ black   -   horn switch
Memory Seat 1 blue/green   -   memory seat switch on seat
Memory Seat 2 blue/black   -   memory seat switch on seat
Memory Seat 3 N/A   -     
Interface Module: Category:
Immobilizer Bypass Required:
Yes Type:
Transponder
Part #: 556UW
Alternate Part1 #: 555U
Notes: Standard on all models.
      
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.
Pearl96Max 
Member - Posts: 16
Member spacespace
Joined: July 21, 2002
Location: United States
Posted: May 20, 2005 at 10:52 PM / IP Logged  
From what Ive seen so far not all the wires are 100% accurate for the '05 models. Please test and confirm all colors prior to using.
Good luck

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer