the12volt.com spacer
the12volt.com spacer
the12volt.com - Free Technical Information for Mobile Electronics Installers, Enthusiasts, and Do-It-Yourselfers since 1999 Find an Installer Near You! - Add your listing to our Installer Database.
the12volt.com spacer
the12volt.com - Free Technical Information for Mobile Electronics Installers
the12volt.com - Free Technical Information for Mobile Electronics Installers
BasicsCar AudioCar SecurityCruise ControlsDiodesDoor LocksOhm's LawPassive CrossoversRelaysResistorsSubwoofer Enclosures Search
the12volt.com - Free Technical Information for Mobile Electronics Installers
the12volt.com - Free Technical Information for Mobile Electronics Installers
the12volt.com - Free Technical Information for Mobile Electronics Installers
Application GuideCalculators, Charts, DiagramsDownloads/ManualsFind InstallersForumsGlossarySubwoofer WiringToolsVehicle Wiring Recent Topics
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
  the12volt.com spacer

the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Diodes
Glossary of Terms
Ohm's Law
Relays
Resistors
Tools and Equipment
Wire Sizes
Introduction
Parallel & Series Calcs
Passive Crossovers
Port Length Calculators
Subwoofer Box Calculators
Subwoofer Enclosure Types
Subwoofer Wiring Wizard
Thiele - Small Parameters
Miscellaneous
Relay Diagrams
Vehicle Wiring Database
Introduction
Alarm Accessories
Alarm Modules
Alarm Sensors
Basic Connections
Illuminated Entry
Light Flash
Power Door Locks
Starter Interrupts
Installation Pictorials
Relay Diagrams
Vehicle Wiring Database
Introduction
Electrical Connections
Mechanical Connections
Servo Settings
VSS and Tach Info
Vehicle Wiring Databse
All Forums
Buy & Sell Equipment
Car Audio
Car Audio Hot Topics
Car Security & Convenience
Car Security Hot Topics
Car Security Pictorials
Cellular & Communications
Cruise Controls
Employment
Fiberglass & Fabrication
General Discussion
Lights, Neon, LEDs, HIDs
Marine Electronics
Miscellaneous
Mobile Video & Navigation
Motorcycle Electronics
Music, Favorite Songs
Relays
Rides & Systems Gallery
Vehicle Information
Recent Forum Topics
Forum Help & How To
Forum & Site Notices
Books & DVDs
Calculators
Charts
Diagrams
Downloads - Manuals
Find an Installer
Forums - Q&A
Glossary of Terms
Insurance for Car Stereos
Links
Mobile Tech News
Relay Diagrams
The Application Guide
Vehicle Wiring Database
About the12volt
Support Us
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer

 
the12volt.com spacer

the12volt's install bay
Mobile Electronics Forums

Welcome Guest :)
Display List of Forum MembersMember List  Forum SearchSearch  RegisterRegister  LoginLogin
Custom Search
the12volt`s installbay - Mobile Electronics Forums the12volt's install bay / Car Security and Convenience

Subject Topic: Wiring Info, 2006 Tundra D/C V8 (Topic Closed Topic Closed)

Post ReplyPost New Topic
the12volt's install bay
Author
Message      << Prev Topic  |  Next Topic >>
jpease
Member
Member
spacespace

Joined: November 01, 2006
Location:
United States
Posts: 9
Posted: November 20, 2006 at 9:26 AM - IP Logged  

Looking for wiring information for Toyota Tundra 2006 X-SP Double Cab (Full 4 Doors)

V8, automatic, power windows, power locks, no OEM alarm,

Back to Top Search for other posts by jpease
Hi Guest
Not a member?
Register

Already a member?
Sign In  
KarTuneMan
Platinum
Platinum
spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace

Joined: December 14, 2004
Location:
Isle Of Man
Posts: 7,080
Posted: November 20, 2006 at 10:13 AM - IP Logged  

 MODEL YEAR(S)
 TUNDRA DOUBLE CAB  2004 -2006
 KEY T-HARNESS IMMOBILIZER
  N/A   TOY-1   N/A
 PART  COLOR LOCATION
 12 VOLT CONSTANT  WHITE/RED (+) and WHITE/BLUE (+)   IGNITION SWITCH HARNESS
 STARTER BLACK/WHITE (+)  IGNITION SWITCH HARNESS
 STARTER 2 N/A 
 IGNITION 1 BLACK/RED (+) IGNITION SWITCH HARNESS
 IGNITION 2 BLACK/YELLOW (+) IGNITION SWITCH HARNESS
 IGNITION 3 N/A  
 ACCESSORY/HEATER BLOWER 1 PINK (+)  IGNITION SWITCH HARNESS
 ACCESSORY/HEATER BLOWER 2 N/A  
 KEYSENSE YELLOW/GREEN (-)  IGNITION SWITCH HARNESS
 PARKING LIGHTS ( - ) GREEN (-)  @ HEADLIGHT SWITCH or BCEU, WHITE Plug, PIN 14, See NOTE *2
 PARKING LIGHTS ( + ) GREEN (+)  IN DRIVERS KICK PANEL, HARNESS to REAR of VEHICLE
 POWER LOCK See NOTE *1  See DIAGRAM
 POWER UNLOCK See NOTE *1  See DIAGRAM
 DOOR TRIGGER See NOTE *3  @ BECU, See NOTE *2
 DOMELIGHT SUPERVISION BLUE/BLACK (-), Requires Part #775 Relay  @ IGNITION KEY CYLINDER ILLUMINATION
 TRUNK RELEASE N/A  
 SLIDING POWER DOOR N/A  
 HORN BLACK/YELLOW (-)  @ BECU, BLACK Plug pin 21, See NOTE *2
 TACH WHITE/BLUE (-)  @ ECM, RIGHT Plug, Pin 5, See NOTE *4
 WAIT TO START LIGHT N/A  
 BRAKE GREEN/WHITE (+) or WHITE/RED (+)  @ SWITCH ABOVE BRAKE PEDAL
 FACTORY ALARM DISARM  DISARMS with KEYSENSE wire, See NOTE *5  @ IGNITION SWITCH HARNESS
 ANTI-THEFT N/A  
 EXTRA INFORMATION
 NOTE *1 this vehicle will requires extra parts when connecting for the KEYLESS ENTRY System, an extra Relay part #775 and diodes, to connect, See DIAGRAM NOTE *2 the BECU (Body Electronic Control Unit) is located above the DRIVERS KICK PANEL, next to the FIREWALL. NOTE *3 the DRIVERS DOOR is a GRAY/RED (-), GRAY Plug, Pin 15, the PASSENGER DOOR is a LIGHT GREEN/BLACK (-) BLACK plug pin 8, the DRIVERS REAR DOOR is a RED/WHITE (-) GRAY plug, pin 16, the PASSENGER REAR DOOR is a RED/WHITE (-) BLACK plug pin 4. When connecting to an ALARM SYSTEM, use all (4) DOOR TRIGGER wires and DIODE ISOLATE, to connect, See DIAGRAM. NOTE *4 the ECM (Engine Control Module) is located behind the GLOVE BOX. NOTE *5 THE KEYSENSE WIRE WILL DISARM THE VEHICLE WITHOUT UNLOCKING THE DOORS BY APPLYING A (-)NEGATIVE TO THIS WIRE DURING REMOTE STARTING.
Back to Top Search for other posts by KarTuneMan
jpease
Member
Member
spacespace

Joined: November 01, 2006
Location:
United States
Posts: 9
Posted: November 20, 2006 at 12:34 PM - IP Logged  

Thanks for your help, in ref Note #1 diagram is there a link to the diagram?
Back to Top Search for other posts by jpease
thepencil
Silver
Silver
spacespace

Joined: December 16, 2002
Location:
Canada
Posts: 1,529
Posted: November 20, 2006 at 3:29 PM - IP Logged  

DIRECTWIRE™ WIRING INFORMATION - TOYOTA / TUNDRA DOUBLE CAB / 2006 / Remote Start


12volts wht/blue (40A), wht/red (25A)   +   ignition harness
Starter black/white   +   ignition harness
Second Starter N/A       
Ignition black/red   +   ignition harness
Second Ignition black/yellow   +   ignition harness
Third Ignition N/A       
Accessory pink   +   ignition harness
Second Accessory N/A       
Keysense yellow/green   -   ign harn or BECU, black plug, pin 22
Notes: Using the status output wire from the remote start to trigger this wire will disarm the alarm without unlocking the doors.

The BECU (Body ECU) is above the driver kick panel, towards the firewall.
Power Lock see DirectFax document 1070       
Power Unlock see power lock       
Lock Motor blue/red   5wi DKP or BECU, black plug, pin 1
Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall.
Unlock Motor red/black   5wi DKP or BECU, black plug, pin 14
Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall.
Parking Lights+ green   +   driver kick, harness to rear
Parking Lights- green   -   switch or BECU, white plug, pin 14
Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall.
Hazards green/red   -   turn signal flasher below fuse box
Turn Signal(L) green/black   +   turn signal flasher below fuse box
Turn Signal(R) green/yellow   +   turn signal flasher below fuse box
Reverse Light red/black   +   driver kick, gray 8 pin plug, pin 2
Door Trigger blue/red (ajar indicator)   -   BECU, white plug, pin 1
Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall.

The individual door trigger wires are also at the BECU. The LF door is gray/red, gray plug, pin 15. The RF door is lt. green/black, black plug, pin 8. The LR door is red/white, gray plug, pin 16. The RR door is red/white, black plug, pin 4. Use all four wires and diode isolate each.
Dome Supervision blue/black   -   ignition key cylinder illumination
Notes: Also found at the BECU, gray plug, pin 8.

The BECU (Body ECU) is above the driver kick panel, towards the firewall.
Trunk/Hatch Pin N/A       
Hood Pin blue/white   -   pin sw. or BECU, white plug, pin 5
Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall.
Trunk/Hatch Release N/A       
Power Sliding Door N/A       
Factory Alarm Arm arms with lock       
Factory Alarm Disarm disarms with unlock       
Disarm No Unlock use key sense wire       
Tachometer black   ac   ECM, 2nd plug from right, pin 1
Notes: The ECM (Engine Control Module) is behind the glove box.
Wait to start N/A       
Brake Wire white/red or green/white   +   brake pedal switch
Parking Brake lt. green/red   -   switch or BECU, black plug, pin 3
Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall.
Horn Trigger black/yellow   -   switch or BECU, black plug, pin 21
Notes: The BECU (Body ECU) is above the driver kick panel, towards the firewall.
Memory Seat 1 N/A       
Memory Seat 2 N/A       
Memory Seat 3 N/A       
Interface Module: Category:
Immobilizer Bypass Required:
No Type:
N/A
Part #: N/A
Notes:
Interface Module: Category:
Door Lock Interface Required:
No Type:
Data Bus
Part #: IM-Toyota-2
Notes:
Smart Starter Kill Relays: Not Available



      
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed Electronics assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.



37Z_1070.pdf
___________________________________
Be careful whose advice you buy, but be patient with those who supply it.posted_image
Back to Top Search for other posts by thepencil
jpease
Member
Member
spacespace

Joined: November 01, 2006
Location:
United States
Posts: 9
Posted: November 20, 2006 at 8:01 PM - IP Logged  

most appreciated guys!!!!  over the next day or so I will putting down what I want to do with the alarm and how I intend to do it.  Of course, I am looking to read everyones comments.
Back to Top Search for other posts by jpease
Mike M2
Platinum
Platinum
spacespace

Joined: June 29, 2005
Location:
United States
Posts: 2,650
Posted: November 21, 2006 at 6:27 AM - IP Logged  

Easy truck, not many shortcuts to take. Use the supervision wire for door trigger, it catches all 4 doors. I use a coil wire instead of going to the BCM, lots easier. When wiring the 1070 document, use the white/black at the door switch for ground(the metal of the door tends to not make a solid ground going thru the hinges). No immobilizer....
___________________________________
Mike M2
Tech Manager
CS Dealer Services
Back to Top Search for other posts by Mike M2
jpease
Member
Member
spacespace

Joined: November 01, 2006
Location:
United States
Posts: 9
Posted: November 21, 2006 at 3:37 PM - IP Logged  

I have a new Autopage LCD 860 Alarm and here is what I am looking to do:

Remote start
Starter kill switch
Remote windows up and down
Remote door locks
Mercury switc
Battery back up
Extra piezo sirens inside the cabin
Remote placement of the controller/cpu

A little background, I have done a couple of alarms in my days, car and residential audio.  Comments?

Back to Top Search for other posts by jpease


the12volt`s installbay - Mobile Electronics Forums the12volt's install bay / Car Security and Convenience
 

Sorry, you can NOT post a reply.
This topic is closed.

  Post ReplyPost New Topic
Printable version Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum





space
the12volt.com spacer
google plus
Search the12volt.com
Custom Search
Follow the12volt.com: Follow the12volt.com on Facebook
Share, print & email this page:
Wednesday, August 27, 2014 Copyright © 1999-2014 the12volt.com Donate to the12volt.com Privacy Policy Advertising
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
BasicsCar AudioCar SecurityCruise ControlsDiodesDoor LocksOhm's LawPassive CrossoversRelaysResistorsSubwoofer Enclosures Search
the12volt.com - Free Technical Information for Mobile Electronics Installers
the12volt.com - Free Technical Information for Mobile Electronics Installers
the12volt.com - Free Technical Information for Mobile Electronics Installers
Application GuideCalculators, Charts, DiagramsDownloads/ManualsFind InstallersForumsGlossarySubwoofer WiringToolsVehicle Wiring Recent Topics
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com - Free Technical Information for Mobile Electronics Installers, Enthusiasts, and Do-It-Yourselfers since 1999 Donate to the12volt.com
the12volt.com spacer
the12volt.com spacer