2003 Toyota Highlander Wiring

Could anyone give me the alarm wiring information for 2003 Toyota Highlander please ? Thanksmikelo

|       ITEM      |     WIRE COLOR     |POL|       WIRE LOCATION        |

|              12V|white & blu/yel     |+  |ignition harness            ||          STARTER|BLACK/ white         |+  |ignition harness            ||         IGNITION|black               |+  |ignition harness            ||  SECOND IGNITION|BLACK / YELLOW        |+  |ignition harness            ||        ACCESSORY|pink                |+  |ignition harness            ||       POWER LOCK|see direct fax      |   |                            ||     POWER UNLOCK|document #1070      |   |                            ||       LOCK MOTOR|BLACK/ white         |   |17 pin plug, pin 1 @ BECU *1||     UNLOCK MOTOR|blue/red            |   |17 pin plug, pin 2 @ BECU *1||    DISARM DEFEAT|blue/black          |   |17 pin plug, pin 6 @ BECU *1|| PARKING LIGHTS +|green               |   |driver kick panel           || PARKING LIGHTS -|GREEN/ red           |   |headlight switch            ||       HEADLIGHTS|RED / blue            |-  |headlight switch            ||     DOOR TRIGGER|GREEN/ YELLOW *2     |-  |ign. key cyl. illumination  || DOME SUPERVISION|comes on with unlock|   |                            ||  TRUNK/HATCH PIN|WHITE/ red           |-  |driver kick panel           ||         HOOD PIN|GREEN/ black         |-  |top plug, pass side junc box||  FCTRY ALARM ARM|arms with lock      |   |                            ||FCTRY ALRM DISARM|disarms with unlock |   |                            || DISARM NO UNLOCK|red to blue *3      |-  |steering column             ||       TACHOMETER|WHITE/ green         |   |28 pin plug, pin 27 @ ECM *4||      SPEED SENSE|wht/red or pur/wht  |   |28 pin plug, pin 22 @ ECM *4||       BRAKE WIRE|GREEN / WHITE         |+  |brake pedal switch          ||     HORN TRIGGER|WHITE/ red           |-  |steering column             ||           WIPERS|lt. green(L), red(H)|+  |steering column             ||  LF WINDOW UP/DN|red - grn/red       |A  |LF window switch            ||  RF WINDOW UP/DN|red - green         |A  |RF window switch            ||  LR WINDOW UP/DN|red - green         |A  |LR window switch            ||  RR WINDOW UP/DN|red - green         |A  |RR window switch            || SUN RF OPN/CLOSE|not recommended     |   |                            ||        RADIO 12V|blue / YELLOW         |+  |radio                       ||     RADIO GROUND|brown               |-  |radio                       ||     RADIO SWITCH|gray                |+  |radio                       || RADIO ILLUMINATE|green               |+  |radio                       ||    POWER ANTENNA|BLACK/ red           |+  |radio                       ||       LF SPEAKER|pink - purple       |   |radio or amplifier *5       ||       RF SPEAKER|lt. green - blue    |   |radio or amplifier *5       ||       LR SPEAKER|black - yellow      |   |radio or amplifier *5       ||       RR SPEAKER|red - white         |   |radio or amplifier *5       |

Notes:

NOTE: Some models have an immobilizer system that needs to be bypassed during remote start.  Use DEI module 555F or 555U to bypass.  *1 The BECU (Body ECU) is behind the glove box, it is the module to the right.  *2 To avoid the dome light delay, go to the Body ECU behind the glove box to get the individual door trigger wires. In the 19 pin plug, the driver door is RED / blue in pin 11 and the rear hatch is WHITE/ red in pin 6. In the 17 pin plug, the front passenger door is RED / blue in pin 16 and the 2 rear door is red in pin 15. Use all wires and diode isolate each.  *3 This is the key sense wire for the ignition switch. The wire changes colors after a junction plug. It is red on the ignition switch side and blue on the other side. Using the status output wire from the remote start to ground this wire will disarm the alarm without unlocking the doors.  *4 The ECM (Engine Control Module) is behind the glove box, it is the module to the left.  *5 The amplifier is under the rear load floor.

Luis

Sound Waves

Is up to the installer to test all wires with a DMM whenever possible.

Luis, Thanks very much ! mikelo