the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2008 Mazda 3 Alarm/Remote Start Wiring


Post ReplyPost New Topic
< Prev Topic Next Topic >
ncreglos 
Member - Posts: 3
Member spacespace
Joined: February 22, 2013
Location: Philippines
Posted: February 22, 2013 at 6:40 AM / IP Logged  
Can anyone give the wiring diagram or information for 2008 Mazda 3.
I would like to install a 2 way security w/ remote start.
Thanks,
Ncreglos
**o**
^^^^^^
offroadzj 
Gold - Posts: 2,043
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: June 03, 2005
Location: New York, United States
Posted: February 22, 2013 at 9:00 AM / IP Logged  
DIRECTWIRE™ WIRING INFORMATION - MAZDA / MAZDA3 / 2008 / Remote Start
[PRINT THIS PAGE]
12volts      BLACK/ red (30A)      +      ignition switch
Notes: If equipped, the Sirius Satellite Radio is under the top center of the dash.
Starter      gray/black      +      ignition switch
Second Starter      N/A           
Ignition      GREEN/ YELLOW      +      ignition switch
Second Ignition      N/A           
Third Ignition      N/A           
Accessory      pink / YELLOW      +      ignition switch
Second Accessory      yellow      +      ignition switch
Keysense      RED / black      +      ignition key switch
Power Lock      GREEN/ red to BLACK/ blue      -1000 ohms      driver kick or PJB, brown 32 pin plug (J-06), pin T
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Power Unlock      same as power lock      -     
Lock Motor      yellow/black      5 wire      driver kick or PJB, 46 pin plug (J-05), pin AP
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Unlock Motor      WHITE/ black      5 wire      driver kick or PJB, 46 pin plug (J-05), pin L
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Parking Lights+      ORANGE / white (L), orange (R)      +      passenger kick or PJB, 46 pin plug (J-05), pins G and AS
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Parking Lights-      BLACK/ white      -      light switch or PJB, 46 pin plug (J-03), pin I
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Hazards      BLACK/ orange      -      hazard switch or PJB, blue 32 pin plug (J-04), pin AC
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Turn Signal(L)      blue      +      passenger kick or PJB, 46 pin plug (J-05), pin A
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Turn Signal(R)      blue/red      +      passenger kick or PJB, 46 pin plug (J-05), pin AK
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Reverse Light      GREEN/ orange (4 door), GREEN/ black (5 door)      +      passenger kick or PJB, 46 pin plug (J-05), pin C
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Door Trigger      BLACK / YELLOW      - N.C.      driver kick or PJB, brown 32 pin plug (J-06), pin W
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Dome Supervision      BLACK/ blue      -      passenger kick or PJB, 46 pin plug (J-05), pin U
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Trunk/Hatch Pin      BLACK/ red      -      pass kick or PJB, brn 32 pin plug (J-06), pin Z (4 door) or X (5 door)
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Hood Pin      BLACK / YELLOW      - N.C.      hood switch or PJB, green 32 pin plug (J-02), pin Y
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Trunk/Hatch Release      N/A           
Power Sliding Door      N/A           
Factory Alarm Arm      BLACK/ blue      -      driver kick or PJB, brown 32 pin plug (J-06), pin Y
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Meter this wire while turning the key in the driver door key cylinder.
Factory Alarm Disarm      BLACK/ white      -      driver kick or PJB, brown 32 pin plug (J-06), pin AA
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Meter this wire while turning the key in the driver door key cylinder.
Disarm No Unlock      use keysense           
Tachometer      BLACK/ stripe (non-turbo) or GREEN/ stripe (turbo)      ac      any fuel injector
Wait to start      N/A           
Brake Wire      RED / white to RED / yellow      +      brake switch, driver kick, or PJB, 46 pin plug (J-05), pin M
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Parking Brake      BLACK/ lt. green      -      parking brake switch or PJB, blue 32 pin plug (J-04), pin AB
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Horn Trigger      black      -      horn switch or PJB, blue 32 pin plug (J-04), pin N
Notes: The PJB (Passenger Junction Box) is behind the glove box.
Memory Seat 1      N/A           
Memory Seat 2      N/A           
Memory Seat 3      N/A           
Interface Modules: Not Available
      
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.
What remote start / alarm unit and bypass are you using?
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205
ncreglos 
Member - Posts: 3
Member spacespace
Joined: February 22, 2013
Location: Philippines
Posted: February 22, 2013 at 11:32 AM / IP Logged  
Thanks Kenny, this will help me a lot.
**o**
^^^^^^
ncreglos 
Member - Posts: 3
Member spacespace
Joined: February 22, 2013
Location: Philippines
Posted: February 22, 2013 at 11:36 AM / IP Logged  
I have a Power Teknique 2 way security system w/ remote and a PKFM platform 4 bypass module. Do you think this will work? Do you have a wiring diagram for installing bypass module. My alarm doesn't have a D2D connection, I guest I will go with W2W, But don't know how to do it.
Thank,
**o**
^^^^^^
offroadzj 
Gold - Posts: 2,043
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: June 03, 2005
Location: New York, United States
Posted: February 22, 2013 at 12:33 PM / IP Logged  
I don't have anything for that bypass, but you should be able to find it available either online or from the manufacturer if it did not come with it. I have never installed the Power Teknique so I have no idea about any of those connections etiher.
I prefer to stick with Compustar and iDatalink for all my remote start parts.
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer