viper 5901/ dball immobilizer needed

Home / the12volt's Install Bay / Car Security and Convenience / viper 5901/ dball immobilizer needed (

Topic Closed)

Welcome Guest :)

Members

< Prev Page < Prev Topic Next Topic >

offroadzj

Gold - Posts: 2,043

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: June 03, 2005

Location: New York, United States

Posted: July 22, 2013 at 11:06 AM / IP Logged

I don't have the vehicle info in front of me so you may it connected correctly, but H3/2(RED / White), H3/6(Red), and H3/9(RED / Black) should all be connected to a 12v constant. They are all inputs for the ignition circuits.

Did you test all of the factory wires to make sure they were correct?

Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

bojangle

Member - Posts: 13

Joined: November 16, 2010

Location: Michigan, United States

Posted: July 22, 2013 at 7:11 PM / IP Logged

I am about to go tackle that relay situation. offroadzj- yes i did check everything with my DMM before making connections. thanks for the help guys I'll post back in a few...

smokeman1

Platinum - Posts: 1,588

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: July 22, 2013 at 8:17 PM / IP Logged

Next question, How are you connections made? Solder, crimp, or taped?

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

bojangle

Member - Posts: 13

Joined: November 16, 2010

Location: Michigan, United States

Posted: July 23, 2013 at 4:24 PM / IP Logged

i had them with butt connectors then read that was not a good idea due to the amount of current the ignition wires need/use so i soldered them. almost done with the relay set up.

bojangle

Member - Posts: 13

Joined: November 16, 2010

Location: Michigan, United States

Posted: July 23, 2013 at 4:52 PM / IP Logged

[QUOTE=smokeman1]

Use h2/12 orange with the relay for 2nd accessory. H2/12 would connect to pin 85, pin 87 out to 2nd acc.

H2/12, the manual shows 'h2' has 8 pins. on the harness it does have more as remote start input and aux are added to that harness so just to verify which color and function am I using H2/12 for?

bojangle

Member - Posts: 13

Joined: November 16, 2010

Location: Michigan, United States

Posted: July 23, 2013 at 5:22 PM / IP Logged

okay so swapping the pins on the 2nd acc relay still same results no power going to the pink ignition wire

bojangle

Member - Posts: 13

Joined: November 16, 2010

Location: Michigan, United States

Posted: July 23, 2013 at 5:28 PM / IP Logged

presumably the dball immobilizer may be causing the issue. Problem is I'm not 100% sure where the wires go as far as going W2W

bojangle

Member - Posts: 13

Joined: November 16, 2010

Location: Michigan, United States

Posted: July 23, 2013 at 8:02 PM / IP Logged

i had an old viper 5701 brain sitting around so i decided to swap them out and it fired right up. looks the brain took a doodie...

offroadzj

Gold - Posts: 2,043

Joined: June 03, 2005

Location: New York, United States

Posted: July 23, 2013 at 9:14 PM / IP Logged

Seems pretty typical of many DEI units lately...

Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

bojangle

Member - Posts: 13

Joined: November 16, 2010

Location: Michigan, United States

Posted: July 24, 2013 at 12:08 PM / IP Logged

is there a way to update the firmware on the brain itself?

< Prev Page

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

viper 5901/ dball immobilizer needed

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.