2013 dodge won't remote start

Home / the12volt's Install Bay / Car Security and Convenience / 2013 dodge won't remote start

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

nismo_monster

Member - Posts: 6

Joined: March 02, 2015

Location: Kansas, United States

Posted: March 02, 2015 at 6:24 PM / IP Logged

Hi I installed a viper 5906v with a dball2 on 2013 dodge ram everything works but it will not remote start the bypass is receiving all signals but still nothing any help is appreciated

tedmond

Gold - Posts: 4,610

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: January 06, 2007

Location: Ontario, Canada

Posted: March 02, 2015 at 6:51 PM / IP Logged

any diagnostics?

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

nismo_monster

Member - Posts: 6

Joined: March 02, 2015

Location: Kansas, United States

Posted: March 02, 2015 at 6:54 PM / IP Logged

No it just cycles the three times and then shuts down but does not give any diagnostics

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: March 02, 2015 at 7:03 PM / IP Logged

look at the number of parking light flashes. After the failed start. You must have parking lights connected or listen for relay clicks from the unit

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

nismo_monster

Member - Posts: 6

Joined: March 02, 2015

Location: Kansas, United States

Posted: March 02, 2015 at 7:07 PM / IP Logged

I did but it doesn't give me any I was expecting it bu got nothing

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: March 02, 2015 at 8:38 PM / IP Logged

cranks at least?

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

nismo_monster

Member - Posts: 6

Joined: March 02, 2015

Location: Kansas, United States

Posted: March 02, 2015 at 8:41 PM / IP Logged

I wish it did but no the dash lights come on and you can hear the relays cycle three times but does not crank and does not give any error codes everything else functions properly lock unlock parking lights ect.

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: March 02, 2015 at 9:18 PM / IP Logged

you should check the following. If you have no dash lights, you have an issue with the Gray/Black (+) from the DBALL2 Red connector. Verify connection to the ignition.

Secondly, check can high and can low of pin 6 and 14.

Lastly, Check the immobilizer wire and ensure you have the correct car vs connector side.

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

nismo_monster

Member - Posts: 6

Joined: March 02, 2015

Location: Kansas, United States

Posted: March 02, 2015 at 9:23 PM / IP Logged

Sorry for the bad grammar I do have dash lights. It is hooked up in d2d and is running a thchd3 t harness so can bus should all be right

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: March 02, 2015 at 9:43 PM / IP Logged

if the connector isn't plugged in or has bent pins, it wont start. check ignition and turn on switch

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.