Viper 5706V and DB-ALL2

Hey guys, I'm going to be installing a Viper 5706V remote start with alarm in my car, and I will be using the Expresskit DBALL2. I want to make sure I have all the connections I need figured out...      VIPER CONNECTIONS         H1/1     (+)12V CONSTANT INPUT        (+)12V CONSTANT H1/2     (-) CHASSIS GROUND  GROUND TO CHASSIS      H1/3     (+) SIREN OUTPUT HOOK TO (+) SIREN      H1/4     PARKING LIGHT ISOLATION N/A      H1/5     PARKING LIGHT OUTPUT        N/A      H1/6     (-)500 mA GROUND WHEN ARMED N/A      H2/1     FLEX RELAY CONTROL OUTPUT      N/A      H2/2     (-) NEUTRAL SAFETY INPUT       GROUND TO CHASSIS      H2/3     (-) 2ND STATUS/REAR DEFOGGER   N/A      H2/4     (-) OEM ALARM DISARM N/A      H2/5     (-) TRUNK RELEASE OUTPUT       N/A      H2/6     (-) DOOR TRIGGER INPUT     GREEN N/A      H2/7     (-) DOME LIGHT SUPERVISION OUT N/A      H2/8     (-) HORN HONK OUTPUT N/A      H2/9     (-) STATUS OUTPUT N/A      H2/10     (-) IGNITION 1 OUTPUT N/A      H2/11     (-) AUX 3 OUTPUT N/A      H2/12     (+) DOOR TRIGGER INPUT N/A      H2/13     (-) AUX 1 OUTPUT N/A      H2/14     (-) AUX 2 OUTPUT N/A      H2/15     (-) AUX 4 OUTPUT N/A      H2/16     (+) BRAKE SHUTDOWN INPUT       BRAKE SWITCH      H2/17     (-) HOOD PIN INPUT TO HOOD PIN      H2/18     (-) STARTER OUTPUT N/A      H2/19     (-) TRUNK PIN/INSTANT TRIGGER N/A      H2/20     (-) DIESEL WAIT TO START INPUT N/A      H2/21     (-) REMOTE START/TURBO TIMER   N/A      H2/22     (-)200mA ACCESSORY OUTPUT      N/A      H2/23     TACHOMETER INPUT N/A      H2/24     (-) OEM ALARM ARM OUTPUT       N/A      H3/1     IGNITION 1 INPUT/OUTPUT     PINK   IGNITION WIRE      H3/2     FLEX RLAY (+)12V INPUT (FUSED) 12V CONSTANT      H3/3     ACCESSORY OUTPUTN/A      H3/4     STARTER OUTPUT     N/A      H3/5     STARTER INPUT     N/A      H3/6     IGNITION 1 (+)12V INPUT(FUSED) 12V CONSTANT      H3/7     FLEX RELAY OUTPUT IGNITION WIRE      H3/8     FLEX RELAY INPUTN/A      H3/9     ACCESSORY/STARTER RELAY(FUSED) 12V CONSTANT      H3/10   EMPTY      NO PINS ON DOOR LOCK HARNESS USED              DBALL2 CONNECTIONS         12/1     RAP OFF   TO DRIVER DOOR SENSE TRIGGER      12/3     DOOR STATUS OUTPUT      N/A      12/4     TRUNK STATUS OUTPUT     N/A      12/5     TACH OUTPUT N/A      12/6     BRAKE STATUS OUTPUT     N/A      12/7     ACCESSORY OUTPUT     TO ACCESSORY WIRE 14/1     SINGLE WIRE CAN     TO PIN 1 ON OBD PORT      14/10     IMMO CONSTANT (CAR SIDE)    TO CAR SIDE OF IMMOBILIZER WIRE 14/11     IMMO CONSTANT (CONN. SIDE) TO CONNECTOR SIDE OF IMMO. WIRE 14/13     (+)12V          N/A      14/14     (-)GROUND  N/A           CONNECTOR 10 NOT USED AT ALL.              CONNECTOR 4 HAS D2D CABLE, CONNECTED TO D2D PORT ON VIPER.        

Forgot to add, car is a 2010 Chevy Malibu LS

Use D2D follow the DBALL2 install guide this car is easy. You wont have to hard wire the brake wire the DBALL2 takes care of that for you. You only have to do it on some Saturns. You can get 12v constant at the BCM. Only other wires you have to hook up from the 5706 are ignition, ground, hood pin and parking lights. The DBALL2 takes care of all other connections.

Forgot you will also have to ground the neutral safety wire on the brain.

Dairyboy sorry to be a pain but don't forget the siren