WIring 2013 RX350/Viper4806/ADS-ALCA

Hello all I am doing remote start Viper 4806V with ADS-ALCA. Can someone please help me with the wiring? Correct me if I am wrong in anyway, thanks. Vehicle Information:          2013 RX350                Remote Start Unit:          VIPER 4806V                Bypass Module:          ALCA-ALA                           Remote Start 4806v               Vehicle           Connection     Color     Description     Color     Polarity     Location:                 THICK HARNESS           Red     12v     White     +     under dash fuse      Red white     12v     White     +     under dash fuse      Red black     12v     White     +     under dash fuse      pink     ignition 1     Green     +     power management control ecu      pink/white     ignition 2     Black     +     power management control ecu      Accessory 1     Orange     Gray     POSITIVE     power management control ecu      Starter 1     Violet     Light Green     +     power management control ecu      starter 2     Pink/black connect to additional relay to power up      black     -     power management control ecu           the second starter?                                           MAIN HARNESS 6-PIN           Red     12v     White     +     under dash fuse      Black     Ground     chassis      -     Ground      Brown     not used                     White     Light Flash Relay PIN 30     Purple     -     Main body ECU           Do I need to connect this wire and how?                     Orange     not used                                Door lock 3-pin           Not used as Bypass will do this                      Aux/Shutdown/trigger 24-Pin harness                      1, 2, 3, 4, 5 6, 7, 8     Not used                     9, 11, 12, 14, 15, 16     Not used                     18 19 20 21 22 23 24     Not used                                Blue     factory horn input (use jumper to Negative)     White     -     Harness at Steering column      BLACK/ white     Ground     chassis ground                Pink     not used                                                 Idatalink ALCA-ALA               Vehicle           Connection     Color     Description     Color     Polarity     Location:                 PURPLE / Black - RX      RX     PINK     DATA     MAIN BODY ECU                 WHITE/ black-SLP     OUTPUT     GREEN     -     STEERING LOCK      White     GROUND INPUT                                BROWN / RED     CAN H     PURPLE     DATA     OBD II      BROWN / yellow     Can L     Red     DATA     OBD II      ORANGE / black     ground input     chassis                ORANGE / white     Tx     Light Green     Data     MAIN BODY ECU      Pink     ignition input to Pink Ignition 1 Input on 8-pin Thick Harness                                Blue/Red     Ground                     Blue / YELLOW-PTS     Not used                dcd

First, you must flash the ADS AL-CA bypass module with the DBI-AL(DL)-TL2 firmware. This will allow 2way D2D communication between the Viper and the ADS AL-CA. Next you should down load this ADS AL-CA w/DBI-AL(DL)-TL2 firmware install guide : https://images.idatalink.com/corporate/Content/Manuals/DL-TL2/DBI-AL(DL)-TL2-EN_20160407.pdf You will follow the Type 2 install guide to the letter. Please note that it specifically says : WARNING: DO NOT CONNECT ANY OTHER ACCESSORY,IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLING THE REQUIRED VEHICLE POWER AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. Also, be aware that the remote started engine will shutdown when the door is opened. There is no take-over possible with these PTS Toyota systems.Soldering is fun!

Hello Kreg Where do I get the 12volt wire from the remote start? Is it the same thich RED wire from heavy gauge? Or from the main 6-pin red wire? These wires already have fuses, do i remove the fuses and change them to 7.5amps?dcd

anyone??dcd

Yes power all the red thick wires, and the single red in the 6 pin harness.. I would grab power from the fuse box [Thick white wire]