the12volt.com - Free Technical Information for Mobile Electronics Installers, Enthusiasts, and Do-It-Yourselfers since 1999

Relay Diagrams - Quick Reference

Basics • Car Audio • Car Security • Cruise Controls • Diodes • Door Locks • Ohm's Law • Passive Crossovers • Relays • Resistors • Subwoofer Enclosures

Application Guides • Calculators, Charts, Diagrams • Downloads/Manuals • Find Installers • Forums • Glossary • Subwoofer Wiring • Tools • Vehicle Wiring

Mobile Electronics Basics

Glossary of Terms

Tools and Equipment

Car Audio & Mobile Video

Metra Application Guides

Parallel & Series Calcs

Passive Crossovers

Port Length Calculators

Subwoofer Box Calculators

Subwoofer Enclosure Types

Subwoofer Wiring Options

Thiele - Small Parameters

Vehicle Wiring Database

Car Security & Convenience

Alarm Accessories

Basic Connections

Illuminated Entry

Power Door Locks

Starter Interrupts

Vehicle Wiring Database

Cruise Controls

Electrical Connections

Mechanical Connections

VSS and Tach Info

Vehicle Wiring Databse

Forums

Buy & Sell Equipment

Car Audio Hot Topics

Car Security & Convenience

Car Security Hot Topics

Car Security Pictorials

Cellular & Communications

Cruise Controls

Fiberglass & Fabrication

General Discussion

Lights, Neon, LEDs, HIDs

Mobile Video & Navigation

Motorcycle Electronics

Music, Favorite Songs

Rides & Systems Gallery

Vehicle Information

Recent Forum Topics

Forum Help & How To

Forum & Site Notices

General Information

Downloads - Manuals

Find an Installer

Glossary of Terms

Insurance for Car Stereos

Mobile Tech News

The Application Guide

Vehicle Wiring Database

Et Cetera

About the12volt

Hurricane Katrina

TopGearAutosport.com

AutoAnything.com

GPS Vehicle Tracking

the12volt's install bay
Mobile Electronics Forums

Welcome Guest :)

Custom Search

the12volt`s installbay - Mobile Electronics Forums

the12volt's install bay / Motorcycle Electronics

Topic: resistor 5v to 2.8v and 2.0v

Post Reply

Post New Topic

Author

Message

<< Prev Topic | Next Topic >>

katman1260

Junior Member

Junior Member

Joined: February 10, 2011
Posts: 2

Posted: March 17, 2011 at 10:19 PM - IP Logged

Post Reply

Quote katman1260

Can someone explain what this statment means? I don't understand where both ends of the resisters are being connected? are all resisters connected at one end to 5v source and the other leg to pin (23) and (16) There are 4 resistors and only two connection points?

33k resistor to +5v

(23) and 22k resistor to gnd(16) to obtain 2v and 33k to +5v and

47k to gnd to obtain 2.8v

Search for other posts by katman1260

Hi Guest

Not a member?
Register

Already a member?
Sign In

i am an idiot

Platinum

Platinum

This member consistently provides reliable information

Joined: September 21, 2006
Location:
Louisiana,
United States
Posts: 10,451

Posted: March 18, 2011 at 5:57 AM - IP Logged

Post Reply

Quote i am an idiot

What are you trying to do?

Search for other posts by i am an idiot

KPierson

Platinum

Platinum

This member consistently provides reliable information

Joined: April 14, 2005
Location:
Ohio,
United States
Posts: 3,266

Posted: February 18, 2012 at 2:19 PM - IP Logged

Post Reply

Quote KPierson

It sounds like a voltage divider.

For the first voltage, connect one side of the 33K resistor to 5vdc and the other side to (23) and one leg of a 22K resistor. Connect the other side of the 22K resistor to ground. Where the 33K and 22K resistors connect there will be 2vdc on that connection (according to the voltage divider formula).

For the next voltage connect one leg of a 33K resistor to 5vdc and connect the other leg to the 47K resistor. However, according to the formula this will give you 2.938vdc where the 33K and 47K connect. To get 2.8vdc you would need a 42K resistor.

There is a great voltage divider calculator here: http://www.raltron.com/cust/tools/voltage_divider.asp

Voltage dividers are great for voltage references, but they can not be used to drive anything. This is because the resistors restrict current to virtually nothing. Even trying to pull 1mA you'll pull your voltage way down!
___________________________________
Kevin Pierson

Search for other posts by KPierson

the12volt`s installbay - Mobile Electronics Forums

the12volt's install bay / Motorcycle Electronics

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

Post Reply

Post New Topic

Printable version

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Custom Search

Follow the12volt.com:

Follow the12volt.com on Twitter

Share, print & email this page:

Tuesday, May 22, 2012

•

Copyright © 1999-2012 the12volt.com

•

Donate to the12volt.com

•

•

•

Free Sitemap Generator

Basics • Car Audio • Car Security • Cruise Controls • Diodes • Door Locks • Ohm's Law • Passive Crossovers • Relays • Resistors • Subwoofer Enclosures

Application Guides • Calculators, Charts, Diagrams • Downloads/Manuals • Find Installers • Forums • Glossary • Subwoofer Wiring • Tools • Vehicle Wiring

the12volt.com - Free Technical Information for Mobile Electronics Installers, Enthusiasts, and Do-It-Yourselfers since 1999

Donate to the12volt.com

It appears that you are using an older browser or your browser does not support JavaScript, or you have it disabled. This site takes advantage of newer features. High Color or better, and a 6.0 browser or the latest version is required with JavaScript and Style Sheets enabled. Don't miss out!