|
|
the12volt's install bay
Mobile Electronics Forums |
|
Welcome Guest :) |
|
|
 Topic: 2002 acura mdx, python 1400xp
|
  |
|
| Author |
|
|
mjakaz
Joined: December 08, 2011
Location:
Indiana,
United States
Posts: 5 |
| Posted: December 08, 2011 at 11:47 AM - IP Logged |
|
|
Can anyone assist me in installing this system, maybe a step by step procedure for dummies lol. Ive never installed one of these before but done other car electronics stuff, even soldering. Sure i can do it w help.
Id greatly appreciate it! |
|
| Back to Top |
 |
|
|
Hi Guest
Not a member?
Register
Already
a member?
Sign In
|
|
|
|
offroadzj
Joined: June 03, 2005
Location:
New York,
United States
Posts: 1,240 |
| Posted: December 08, 2011 at 11:54 AM - IP Logged |
|
|
There really isn't a step by step how to. Get a wire diagram for your car, get the wire diagram from the python, match up the wires and follow the instructions included with the starter. But to be honest, if you have to ask how to do it, you probably shouldn't be doing it. Making the connections is easy, but knowing how to test and what to test for can get tricky. If you do not know what you are doing 100% you can end up causing a lot of damage that will be VERY costly.
___________________________________
Kenny
Former Installation Manager
Circuit City Roadshop
Store #3160
Albany, NY 12205 |
|
| Back to Top |
|
|
|
mjakaz
Joined: December 08, 2011
Location:
Indiana,
United States
Posts: 5 |
| Posted: February 03, 2012 at 6:45 AM - IP Logged |
|
|
Keyless entry and remote start completed.
If anyone would like some help lmk. If using the PKALL it worked like a charm. Even tho my Python 1400XP system had D2D compatibility it did not work. Took a min to realize but i ended up having to just wire to 12v and ground. Then worked immediately!
Also, the tach and hood pin wire can be found in the car! No need to go thru the firewall. So for a heads up when u run the Lock/Unlock 2 wires to pass side go ahead and run 1 extra for the hood pin. The tach is on the drivers side. I found these after a couple hrs of trouble shooting w a DVM. What a PITA this install was. Just really time consuming not that its hard.
I do however have 2 issues:
1- When i lock the car w remote start fob the security light will NOT flash. Any pointers?
2- Found out at 5:30am this morning to NOT arm or lock the MDX with the OEM Factory key fob so that the security light WILL flash and then using the remote start fob to start the M. After it started and ran for 15-20 seconds the horn immediately began to go off and would not stop regardless of what button on what remote i used. Finally after 2-3 mins of loudest OEM horns ever it stopped.
Anywho if someone knows what a fix may be id greatly appreciate it. This was my first install on remote start system and ive tackled just about everything from engine swaps to non navi 06 TL to upgrading the 07-08 TL nav system. I soldered majority of all connections. Only initial issues i had once i attempted to start was the PKALL didnt work until rewired and forgot to plug in my antenna. Ha big whoops there! |
|
| Back to Top |
|
|
|
tedmond
Joined: January 06, 2007
Location:
Ontario,
Canada
Posts: 3,843 |
| Posted: February 03, 2012 at 7:09 AM - IP Logged |
|
|
you dont have the factory alarm arm and disarm wires connected.
connect lock to black/blue (-) @ pkp fuse box
you probably have it connected to black/orange right now.
connect unlock to Orange (-) @ pkp.
set unit to unlock-start-relock or to prevent that run a wire into the driver door, and connect to blue (-) disarm
___________________________________
Ted
P2W901SS
Compustar Pro Dealer
"If your girlfriend yells at the top of her lungs, is that SQ or SPL?" |
|
| Back to Top |
|
|
|
mjakaz
Joined: December 08, 2011
Location:
Indiana,
United States
Posts: 5 |
| Posted: February 03, 2012 at 12:28 PM - IP Logged |
|
|
tedmond wrote:
you dont have the factory alarm arm and disarm wires connected.
connect lock to black/blue (-) @ pkp fuse box
you probably have it connected to black/orange right now.
connect unlock to Orange (-) @ pkp.
set unit to unlock-start-relock or to prevent that run a wire into the driver door, and connect to blue (-) disarm |
|
|
You have a PM
thank u |
|
| Back to Top |
|
|
|
mjakaz
Joined: December 08, 2011
Location:
Indiana,
United States
Posts: 5 |
| Posted: February 04, 2012 at 8:24 AM - IP Logged |
|
|
|
| Back to Top |
|
|
|
mjakaz
Joined: December 08, 2011
Location:
Indiana,
United States
Posts: 5 |
| Posted: February 04, 2012 at 4:15 PM - IP Logged |
|
|
Got it!!!
just wired arm and disarm into the drivers door window switch. Now it works. Security light flashes when i lock and when i start the security light goes out but stays locked. It does not however rearm, is this right? |
|
| Back to Top |
|
|
|
tedmond
Joined: January 06, 2007
Location:
Ontario,
Canada
Posts: 3,843 |
| Posted: February 04, 2012 at 10:49 PM - IP Logged |
|
|
just read the PM, glad you got it to work out.
___________________________________
Ted
P2W901SS
Compustar Pro Dealer
"If your girlfriend yells at the top of her lungs, is that SQ or SPL?" |
|
| Back to Top |
|
|
|
|
If you wish to post a reply to this topic you must first login
If you are not already registered you must first register
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum
|
|
|
|
|
|
| |
Member List
Search
Register
Login
