|
|
the12volt's install bay
Mobile Electronics Forums |
|
Welcome Guest :) |
|
|
 Topic: 2002 2500hd viper 5901 w/ xpress
|
  |
|
| Author |
|
|
lethalopie
Joined: January 14, 2012
Location:
Michigan,
United States
Posts: 10 |
| Posted: January 14, 2012 at 10:42 PM - IP Logged |
|
|
| I have a 2002 2500hd. I am looking to install a viper 5901 with an xpresskit dball. I cant find the install for the xpresskit. Also how to wire the two in together. Any help would be greatly appreciated. |
|
| Back to Top |
 |
|
|
Hi Guest
Not a member?
Register
Already
a member?
Sign In
|
|
|
|
jstruckman
Joined: May 03, 2004
Posts: 424 |
| Posted: January 14, 2012 at 11:16 PM - IP Logged |
|
|
go to directed.com for the installation instructions for the dball.
__________________________________ |
|
| Back to Top |
|
|
|
lethalopie
Joined: January 14, 2012
Location:
Michigan,
United States
Posts: 10 |
| Posted: January 14, 2012 at 11:19 PM - IP Logged |
|
|
| Got that. Now that I install dball, what wires from the viper do I hook up to truck wiring harness |
|
| Back to Top |
|
|
|
kreg357
Joined: January 30, 2009
Location:
New York,
United States
Posts: 2,661 |
| Posted: January 15, 2012 at 5:48 AM - IP Logged |
|
|
Firs,t make sure your DB-ALL is flashed with the 401.GM5 v1.06.01 firmware. Then follow the DB-ALL GM5 Type 6 install
guide diagram. The Remote Starter is shown at the top of the diagram on Page 9. It pretty much lists/shows all the connections.
___________________________________
Soldering is fun! |
|
| Back to Top |
|
|
|
lethalopie
Joined: January 14, 2012
Location:
Michigan,
United States
Posts: 10 |
| Posted: January 15, 2012 at 11:03 AM - IP Logged |
|
|
| What about the alarm part of the viper? |
|
| Back to Top |
|
|
|
offroadzj
Joined: June 03, 2005
Location:
New York,
United States
Posts: 1,240 |
| Posted: January 15, 2012 at 11:18 AM - IP Logged |
|
|
The DB-ALL should give you a lot of your door trigger inputs, etc. So for the Viper you should only need to connect the main ignition wires (make sure to trigger all ignition/accessory wires in that truck), ground, parking lights, tach (from what I've found the DB-ALL tach signal is very unreliable), hood pin.
___________________________________
Kenny
Former Installation Manager
Circuit City Roadshop
Store #3160
Albany, NY 12205 |
|
| Back to Top |
|
|
|
lethalopie
Joined: January 14, 2012
Location:
Michigan,
United States
Posts: 10 |
| Posted: January 15, 2012 at 1:26 PM - IP Logged |
|
|
| When it says you must power second ignition wire for remote start, what do i do? I know 2nd ignition is the white one |
|
| Back to Top |
|
|
|
lethalopie
Joined: January 14, 2012
Location:
Michigan,
United States
Posts: 10 |
| Posted: January 15, 2012 at 1:30 PM - IP Logged |
|
|
| also which wire is the 2nd ignition on the viper
|
|
| Back to Top |
|
|
|
offroadzj
Joined: June 03, 2005
Location:
New York,
United States
Posts: 1,240 |
| Posted: January 15, 2012 at 1:57 PM - IP Logged |
|
|
the viper should have a flex relay output (pink/white) connect that right to the white 2nd ignition wire on the truck and make sure you have all 3 red, red/white, and red/black wires connected to 12v constant power. That truck also has a 2nd accessory wire which you will need to power off of a relay connected as follows:
Pin 86 - 12v constant (fused)
Pin 85 - (-)200ma 2nd accessory output (normally orange on the Viper)
Pin 30 - 12v constant (fused)
Pin 87 - 2nd accessory wire on vehicle.
___________________________________
Kenny
Former Installation Manager
Circuit City Roadshop
Store #3160
Albany, NY 12205 |
|
| Back to Top |
|
|
|
lethalopie
Joined: January 14, 2012
Location:
Michigan,
United States
Posts: 10 |
| Posted: January 15, 2012 at 2:19 PM - IP Logged |
|
|
Man i'm having a hell of a time. this is what I have so far
Remote Start:
+Accessory Output (10 pin orange wire) to orange ign harness
+Brake input (18pin brown wire) to brakes switch white
Parking Lights (12 pin white wire) to brown bcm
Ignition 2 (10pin pink/white) to white ign wire
hood switch (18pin grey) to hood switch
12volt (12pin red wire) to red ign wire
groung(12pin black) to ground
Starter output (10pin violet) to ign yellow wire
Ignition 1 output(18pin pink) to pink ign harness
DBALL:
Ignition input(10pin pink) to pink ign harnes
j1580(purple/yellow 14pin) to purple obd2
R code(violet/green and violet/brown 12pin) to yellow ignition bcm
And i'm supposed to hook up red wire, red/black, red/white from 12pin rs to 12volt constant. Where is the third red wire coming from? |
|
| Back to Top |
|
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum
|
|
|
|
|
|
| |
Member List
Search
Register
Login
