|
|
the12volt's install bay
Mobile Electronics Forums |
|
Welcome Guest :) |
|
|
 Topic: 2000 gmc jimmy, viper 5902
|
  |
|
| Author |
|
|
trafficbuck
Joined: January 08, 2012
Location:
Missouri,
United States
Posts: 21 |
| Posted: February 02, 2012 at 10:56 AM - IP Logged |
|
|
I have connected the Blade AL and this is all that I get tach, dome light, door triggers, door lock & horn, I have not connected any of these w2w.
But I do not get unlock???
All the wiring diagrams that I have seen only show (+) for the door unlock and lock
The instruction for the FT 6000 AS the door locks, unlocks & trunck release to connect with a negative (-) 250mA ??? |
|
| Back to Top |
 |
|
|
Hi Guest
Not a member?
Register
Already
a member?
Sign In
|
|
|
|
offroadzj
Joined: June 03, 2005
Location:
New York,
United States
Posts: 1,240 |
| Posted: February 02, 2012 at 10:58 AM - IP Logged |
|
|
You must connect the 2nd ignition on that car. Not sure about that one in particular but you can cause transmission damage on many GM's by not connecting it. It is listed in the wiring diagrams for a reason...
I am pretty sure you need 2nd accessory hooked up as well for the heater blower. Make sure that if the unit does not have a flex output (which that compustar does not), you MUST use relays on the 2nd ignition and 2nd accessory wires. Connect as follows:
Pin 85 - (-)200ma 2nd ignition output
Pin 86 - 12v constant fused
Pin 87 - 12v constant fused (20amp)
Pin 30 - 2nd ignition wire in vehicle
Pin 85 - (-)200ma 2nd accessory output
Pin 86 - 12v constant fused
Pin 87 - 12v constant fused (20amp)
Pin 30 - 2nd accessory wire in vehicle
___________________________________
Kenny
Former Installation Manager
Circuit City Roadshop
Store #3160
Albany, NY 12205 |
|
| Back to Top |
|
|
|
offroadzj
Joined: June 03, 2005
Location:
New York,
United States
Posts: 1,240 |
| Posted: February 02, 2012 at 11:06 AM - IP Logged |
|
|
Is this another GMC jimmy than in your compustar thread? If not, then there is no need to start another thread. If it is another, just like that 2000 GMC Jimmy, this one will also need a bypass. With idatalink bypasses, the ADS-ALSL GM
will do data immobilizer and tach (similar to the blade-al) and the ADS-TBSL KO or ADS-TBSL PL will jsut do data immobilizer (similar to the blade-tb).
___________________________________
Kenny
Former Installation Manager
Circuit City Roadshop
Store #3160
Albany, NY 12205 |
|
| Back to Top |
|
|
|
trafficbuck
Joined: January 08, 2012
Location:
Missouri,
United States
Posts: 21 |
| Posted: February 02, 2012 at 11:30 AM - IP Logged |
|
|
|
| Back to Top |
|
|
|
tedmond
Joined: January 06, 2007
Location:
Ontario,
Canada
Posts: 3,843 |
| Posted: February 02, 2012 at 11:31 AM - IP Logged |
|
|
as metz suggested.
The AL on that car does passlock and tach. That is it.
The TB does passlock only
NO other features are supported as you suggested (locks, domelight, etc)
you will have to make analog connections to the vehicle. the locks are negative from the unit. if the vehicle uses positive locks use 2 relays
85 - lock or unlock from compustar
86 - constant 12v
87 - constant 12v
30 - lock or unlock on vehicle
___________________________________
Ted
P2W901SS
Compustar Pro Dealer
"If your girlfriend yells at the top of her lungs, is that SQ or SPL?" |
|
| Back to Top |
|
|
|
trafficbuck
Joined: January 08, 2012
Location:
Missouri,
United States
Posts: 21 |
| Posted: February 02, 2012 at 11:33 AM - IP Logged |
|
|
Thank you,
This is different GMC then I posted for the compustar. |
|
| Back to Top |
|
|
|
tedmond
Joined: January 06, 2007
Location:
Ontario,
Canada
Posts: 3,843 |
| Posted: February 02, 2012 at 11:44 AM - IP Logged |
|
|
if you use the viper the fortin evo-all will work good for your application. does locks, trunk, tach, and bypass.
w2w only.
___________________________________
Ted
P2W901SS
Compustar Pro Dealer
"If your girlfriend yells at the top of her lungs, is that SQ or SPL?" |
|
| Back to Top |
|
|
|
trafficbuck
Joined: January 08, 2012
Location:
Missouri,
United States
Posts: 21 |
| Posted: February 02, 2012 at 1:19 PM - IP Logged |
|
|
|
| Back to Top |
|
|
|
|
If you wish to post a reply to this topic you must first login
If you are not already registered you must first register
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum
|
|
|
|
|
|
| |
Member List
Search
Register
Login
