|
|
the12volt's install bay
Mobile Electronics Forums
|
|
 Topic: 2003 toyota highlander wiring ( Topic Closed)
|
  |
 |
| Author |
|
|
the knight
Joined: January 20, 2004
Location:
United States
Posts: 1 |
| Posted: January 20, 2004 at 7:30 AM - IP Logged |
|
|
| i am looking for the wiring diagram for the 2003 toyota highlander for alarm and remote start. |
|
| Back to Top |
 |
|
|
Hi Guest
Not a member?
Register
Already
a member?
Sign In
|
|
|
|
tblanning
Joined: March 28, 2003
Location:
United States
Posts: 60 |
| Posted: January 20, 2004 at 9:44 PM - IP Logged |
|
|
Remote Starter Wiring Colors and Notes |
Function | | Vehicle Color | Location | Start: | | Black/White (+) | Ignition switch harness | Ignition #1: | | Black (+) | Ignition switch harness* | Ignition #2: | | Black/Yellow (+) | Ignition switch harness | Ignition #3: | | red (Key Sense Wire) | *** | Accessory: | | Pink (+) | Ignition switch harness | Brake Light: | | Green/White (+) | Brake pedal switch | Tach Signal: | | White/Green (AC) | In harness at the ECM** | Parking Lights: | | Green (+) | Drivers kick panel | Headlights: | | N/A | | Diesel Glow Plug: | | N/A | | Clutch Bypass Wire: | | N/A | | NOTES: *This vehicle is equipped with a Transponder Anti-Theft security system. Use Universal Alarm Bypass Module part #2x402 where X can be any number. **The Engine Control Module (ECM) is behind the glove box, it is the module to the left of the glove box. *** The key sense wire will measure 12 volts all the time till you place the key inside the ignition switch and the key sense wire will ground. Connect the white/black wire from the unit (ignition 3) to the wire and that will disarm the OEM factory alarm. |
Alarm and Keyless Entry Wiring Colors |
Function | | Vehicle Color | Location | Constant +12 Volts: | | White & Blue/Yellow (+) | Ignition switch harness | OEM Alarm Disarm: | | Use key sense wire | | Dome Lights/Superv: | | Comes on with unlock | | OEM Horn: | | White/Red (-) | Steering column harness | Power Lock: | | See note below | *** | Power Unlock: | | See note below | *** | Trunk Release: | | N/A | | Alarm Input Wire: | | Comes on with unlock | | NOTES: ***See Installation Note #212 Modern Toyota Door Locks Diagram. Installation Note #212 Interfacing to Lexus and Toyota Door Lock Systems Toyota and Lexus have made radical changes to their door lock system. Gone are the days of simple negative trigger. In order to lock the doors you must now ground the lock wire while interupting the detection wire. To unlock the doors you must provide a negative trigger to the detection wire and the unlock wire at the same time - all this while keeping the wires completely isolated from each other. With the exception of the Highlander, Tacoma, and IS, the diagram below must be connected inside the PASSENGER door. 
|
|
|
| Back to Top |
|
|
|
markcars
Joined: December 11, 2002
Location:
United States
Posts: 644 |
| Posted: February 15, 2004 at 9:49 AM - IP Logged |
|
|
Hi Tblanning,
I think the link to the picture is pointing somewhere that we cannot view. (Looks like en E: drive by mistake)st? Can you please show us the picture?
Also any more information regarding alarming and remote starting the 2003 highlander would be most helpful.
Thank you so much,
Mark |
|
| Back to Top |
|
|
|
markcars
Joined: December 11, 2002
Location:
United States
Posts: 644 |
| Posted: March 02, 2004 at 12:12 PM - IP Logged |
|
|
I found the diagram finally.
Thanks |
|
| Back to Top |
|
|
|
|
Sorry, you can NOT post a reply.
This topic is closed.
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum
|
|
|
|
|
|
|
Member List
Search
Register
Login
