|
|
the12volt's install bay
Mobile Electronics Forums |
|
Welcome Guest :) |
|
|
 Topic: 2006 Toyota Sienna alarm wiring ( Topic Closed)
|
  |
|
| Author |
|
|
stephen0715
Joined: February 05, 2006
Posts: 15 |
| Posted: February 26, 2006 at 12:01 AM - IP Logged |
|
|
Need wiring diagram of 2006 toyota sienna for installing alram. Anyone can help? Thanks! |
|
| Back to Top |
 |
|
|
Hi Guest
Not a member?
Register
Already
a member?
Sign In
|
|
|
|
Mike M2
Joined: June 29, 2005
Location:
United States
Posts: 2,466 |
| Posted: February 26, 2006 at 8:33 AM - IP Logged |
|
|
DIRECTWIRE™ WIRING INFORMATION - TOYOTA / SIENNA / 2006 / Remote Start
[PRINT THIS PAGE]
| 12volts | wht/red (30A), wht/blue (7.5A) | + | ignition harness | | Starter | black/yellow | + | ignition harness | | Second Starter | N/A | | | | Ignition | black | + | ignition harness | | Second Ignition | black/yellow | + | ignition harness | | Third Ignition | N/A | | | | Accessory | pink | + | ignition harness | | Second Accessory | N/A | | | | Keysense | blue/black | - | ignition harness | | Notes: Using the status output to trigger this wire during remote start will disarm the factory alarm without unlocking the doors. | | Power Lock | lt. green | - | driver kick, 18 pin plug | | Notes: Meter these wires while turning the key in the driver door key cylinder. | | Power Unlock | blue (double pulse) | - | driver kick, 18 pin plug | Notes: Meter these wires while turning the key in the driver door key cylinder.
Can also use the passenger door key cylinder wire for unlock, which only requires a single pulse. It is blue/yellow (-) in the passenger kick in a 12 pin plug. | | Lock Motor | blue/red | 5wi | driver kick, 12 pin plug | | Unlock Motor | white/red to red | 5wi | driver kick, 18 pin plug | | Parking Lights+ | do not use, relay rests at gnd | | | | Parking Lights- | green/black | - | headlight switch | | Hazards | black/orange | - | hazard switch | | Turn Signal(L) | green/black | + | R side of fuse box, 30 pin plug | | Turn Signal(R) | green/yellow | + | R side of fuse box, 30 pin plug | | Reverse Light | red/black | + | driver kick, harness to rear | | Door Trigger | blue | - | interior light switch on dash | Notes: Can also use individual door trigger wires. The driver door is red/yellow in the 16 pin plug, pin 14 at the BECU. The passenger door is red/yellow in the 28 pin plug, pin 23 at the BECU. The left sliding door is gray, pin 19, in a 25 pin plug on the right side of the fuse box. The right sliding door is red/white in the 16 pin plug, pin 16 at the BECU. The hatch door is green/white in the 28 pin plug, pin 25 at the BECU. Use all wires and diode isolate each.
The BECU (Body ECU) is attached to the back of the fuse box under the driver side dash. | | Dome Supervision | red/green | - | interior light switch on dash | | Trunk/Hatch Pin | common with door trigger wire | | | | Hood Pin | red/white | - | BECU, 10 pin plug, pin 10 | | Notes: The BECU (Body ECU) is attached to the back of the fuse box under the driver side dash. | | Trunk/Hatch Release | yellow/red (power back door) | - | bottom L of fuse box, 22 pin plug | Notes: On vehicles without the power back door, the hatch release is green/black (-) at the BECU, 28 pin plug, pin 3. Meter this wire while open the hatch from the handle on the rear hatch.
The hatch release motor wire is blue/black (+) at the BECU, 26 pin plug, pin 1.
The BECU (Body ECU) is attached to the back of the fuse box under the driver side dash. | | Power Sliding Door | yellow/green (L), purple (R) | - | bottom L of fuse box, 22 pin plug | | Factory Alarm Arm | arms with lock | | | | Factory Alarm Disarm | disarms with unlock | | | | Disarm No Unlock | use key sense wire | | | | Tachometer | black/orange | ac | ECM, top plug, pin 5 | | Notes: The ECM (Engine Control Module) is behind the glove box. | | Wait to start | N/A | | | | Brake Wire | green/white | + | brake pedal switch | | Parking Brake | red/white | - | R side of fuse box, 36 pin plug | | Horn Trigger | green/black | - | horn switch | | Memory Seat 1 | pink/blue | - | seat memory switch in door | | Memory Seat 2 | lt. green/black | - | seat memory switch in door | | Memory Seat 3 | N/A | - | |
 | Interface Module: | Category:
Immobilizer Bypass | Required:
Yes | Type:
Transponder | | Part #: 556UW | | Alternate Part1 #: DesignTech 20402 | | Alternate Part2 #: DesignTech 29402 | | Notes: Standard on LE, XLE and Limited models. |
|
___________________________________
Mike M2
Tech Manager
CS Dealer Services |
|
| Back to Top |
|
|
|
stephen0715
Joined: February 05, 2006
Posts: 15 |
| Posted: February 27, 2006 at 5:47 PM - IP Logged |
|
|
|
| Back to Top |
|
|
|
automan25
Joined: February 27, 2006
Location:
Singapore
Posts: 1 |
| Posted: February 27, 2006 at 9:06 PM - IP Logged |
|
|
need wiring diagram of 2004 mercedes benz for installing alarm.anyone can help ?thanks!
___________________________________
chan |
|
| Back to Top |
|
|
|
|
Sorry, you can NOT post a reply.
This topic is closed.
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum
|
|
|
|
|
|
| |
Member List
Search
Register
Login
