compustar CN1

Home / the12volt's Install Bay / Car Security and Convenience / compustar CN1 (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

radeon200

Member - Posts: 5

Joined: August 11, 2004

Location: United States

Posted: October 21, 2004 at 9:00 PM / IP Logged

wow, compustar installation guide is a very poor written manual. i hope you compustar expert folks can help. i would like to map out all the wires before i start the installation. On CN1, there are 2 constant power with 30amps that i will cut and attach them near to the battery. if that is good i would like to move on to the relays. the list below is questions on CN1. i have a Dodge Grand Caravan 2005. thanks i appreciate the effort.

CN1

1) red - 12v

2) gr/wh - pking light

3) RED / wh - 12v

relay - blue - 2nd ignition ???

- violet - starter ?????

4) white - accessory

5) violet - relay ???

6) Yellow - relay ??? -

7) red - relay ???

green - ignition -?????

8) black - ground

----------------------------------

3) this wire has a relay out with 2 wires. one of the 2nd ingnition and the other may be for the starter? what about the 3rd ignition that nissan maximas have? i guess i do not need to deal with the 3rd ignition.

5)6)7) are connected to one relay and out from the relay with 2 wires. yellow is for the starter? yellow/blk is for _____?

7) green is for the ignition

Back to Top

darkowy

Member - Posts: 22

Joined: September 14, 2004

Location: United States

Posted: October 23, 2004 at 5:56 AM / IP Logged

Check this link

http://www.compustar.org/support/manuals/wiring_manuals/CM3000_wiring_manual.pdf

Back to Top

ThurzNite

Member - Posts: 24

Joined: June 08, 2002

Location: United States

Posted: December 15, 2004 at 1:45 AM / IP Logged

dood, i jsut spent freakin 2hr trying to figure the wiring diagram out using the basic install manual. Darkowy, if I saw your post earlier, I woulda cut my time down to 0. Well, at least a lot shorter than 2hr. thanx for the link!

Jae

Back to Top

ThurzNite

Member - Posts: 24

Joined: June 08, 2002

Location: United States

Posted: December 15, 2004 at 2:00 AM / IP Logged

Another question. for CN5, wires 1 and 2. They are for Rearm and Arm. I read what they do. Functionally, what could they operate? I'm looking for ideas.

Tbanks.

Jae

Back to Top

darkowy

Member - Posts: 22

Joined: September 14, 2004

Location: United States

Posted: December 15, 2004 at 9:49 AM / IP Logged

You should use those wires to disarm (CN5 Pin 2) and arm (CN5 Pin 1) your factory alarm if your car is equipped with one.

Back to Top

ThurzNite

Member - Posts: 24

Joined: June 08, 2002

Location: United States

Posted: December 18, 2004 at 1:52 PM / IP Logged

I'm just full of questions.

CN1 Pin 3. I understand that the fused wire connects to constant 12v. What about the blue and purple wires coming off the relay? My car (97 nissan maxima) has a 2nd accessory and 2nd starter.

Thanx!

Jae

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

compustar CN1

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.