I have the DEI 551R installed on my 1999 Mazda 626 4cl,and I need help with the following.I want to install the Dei 450T or 450R + 529T to open and close the moonroof +530T to controll the windows+451M for the door locks.Can someone inlighten me with the wiring diagram and any tips or tricks that would guide me thur this install.Also will I need a different remote switch to controll these add on's. Please send help !!
| ITEM | WIRE COLOR |POL| WIRE LOCATION |
| 12V|black (x2) |+ |ignition harness |
| STARTER|green |+ |ignition harness |
| IGNITION|BLACK/ white |+ |ignition harness |
| SECOND IGNITION|BLACK/ red |+ |ignition harness |
| ACCESSORY|blue |+ |ignition harness |
| POWER LOCK|BROWN / yellow |- |*2 |
| POWER UNLOCK|white & brn/wht *3 |- |*2 |
| LOCK MOTOR|green | |drivers kick panel |
| UNLOCK MOTOR|pink | |drivers kick panel |
| DISARM DEFEAT|red | |passengers kick panel |
| PARKING LIGHTS +|WHITE/ red | |green plug at fuse box |
| PARKING LIGHTS -|lt GREEN/ red | |headlight switch |
| HEADLIGHTS|yellow |- |headlight switch |
| DOOR TRIGGER|RED / white |- |green plug at fuse box |
| DOME SUPERVISION|use door trigger | | |
| TRUNK/HATCH PIN|WHITE/ black |- |at light in trunk *5 |
| HOOD PIN| | | |
|TRNK/HTCH RELEASE|orange |- |*2 |
| FCTRY ALARM ARM| | | |
|FCTRY ALRM DISARM| | | |
| DISARM NO UNLOCK|*4 | | |
| TACHOMETER|*1 | |ignition coil |
| SPEED SENSE|gray/blue | |instrument cluster or ECM *6|
| BRAKE WIRE|WHITE/ green |+ |brake pedal switch |
| HORN TRIGGER|grn/red or grn/org |- |steering column |
| WIPERS|blu/wht(L),blu/red(H|+ |steering column |
| LF WINDOW UP/DN|red - RED / blu |A |drivers window switch |
| RF WINDOW UP/DN|grn/wht - RED / blk |A |drivers switch or kick panel|
| LR WINDOW UP/DN|blu/wht - blu/blk |A |drivers switch or kick panel|
| RR WINDOW UP/DN|grn/yel - wht/red |A |drivers switch or kick panel|
Notes:
NOTE: This vehicle has an immobilizer system that needs to be bypassed when adding remote start. See direct fax document #1061 *1 Use red or green for the 4 cylinder and white for the 6 cylinder. *2 Found at two tan modules near the hood release. *3 The white wire will unlock the drivers door only, and the BROWN / white will unlock the other doors. use both wires and diode isolate each. *4 To disarm with out unlocking, send a positive trigger to the blue / YELLOW key sense wire. The key sense wire is located at the steering column. *5 Can also find in drivers kick panel in the harness from the rear if the vehicle has a factory alarm. *6 The ECM is under the center console. The VSS wire is in pin 58.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
thanks for the info Jeff>Now I have aquestion before I make a big mistake and burn s omething out.On my 99 Mazda 626 as noted above.Can I wire the door locks from the 551r as follows: Light blue (-) door unlock output to the power unlock:white & brn/wht *3[- ]*2....and the Light green (-) door lock output to Power lock { BROWN / Yellow [-]*2 directly or do I need to use a relay.Thanks Ron