2009 ford e 350 need alarm diagram
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=108558
Printed Date: June 10, 2024 at 9:19 AM
Topic: 2009 ford e 350 need alarm diagram
Posted By: kassdog
Subject: 2009 ford e 350 need alarm diagram
Date Posted: October 31, 2008 at 11:05 AM
Putting a remote start and alarm into this car and don't want to go at it blind. Directechs doesn't have it as it is different from the 08 model and I'm alread checked this site and bulldog. Any help will be appriciated.
Replies:
Posted By: draggin95niss
Date Posted: October 31, 2008 at 11:28 AM
www.techservices.audiovox.com if u dont already have an account just set one up, its free...also i checked and they have the info your looking for...hope this helps....
Posted By: kassdog
Date Posted: October 31, 2008 at 11:32 AM
The link isn't working for me
Posted By: draggin95niss
Date Posted: October 31, 2008 at 11:42 AM
put in the search bar on yahoo or google and it will bring up th ewebpage in the search...sorry i cant get it to work in the address box either i just did the search thing and when i brought up the page i saved it in my favorites for future needs...
Posted By: kassdog
Date Posted: October 31, 2008 at 11:54 AM
Thanks for the site but unfortunetely those aren't the right colors either. Its wierd. I've been testing for all of these wires and they are completely different. I'll post em up in another topic once I'm finished with the car.
Posted By: draggin95niss
Date Posted: October 31, 2008 at 11:59 AM
well it was worth a shot...sorry i couldnt help..
Posted By: wass0026
Date Posted: January 04, 2009 at 2:04 AM
Hey there I was doing a search and I ran across your post. I just installed a remote start in a 2009 ford e series and ran into the same dilemma with my wire colors on my tech sheet not matching my vehicles colors. I installed the full unit and everything works fine as far as the functionality of the starter and the door locks. However the parking light circuit was a bit goofy. One of the wires tested at ground on rest then when the switch was engaged raised to 8 volts. Another wire, this one I remember being gray; rested at 6 volts and then switched to ground with the parking lights. I tried introducing voltage onto them(It was fused, however I still think this was a mistake), and nothing worked. So I left it unhooked for the meantime. Somehow through my self discovery of the 09 e series it seems I have taken out the lighting for the transmission indicator on the instrument cluster, this is the only thing not lighting up. I checked all-data and there not listing an 09 yet. If anyone knows anything that might save me some diagnosing time it would be great, thanks.
Posted By: loneranger
Date Posted: January 04, 2009 at 2:46 AM
Posted By: i am an idiot
Date Posted: January 04, 2009 at 8:11 AM
wass, I have repaired many of the light switches on the newer Ford F series vehicles. Usually the failure is the entire lighting system fails, you may have the same problem, just in a smaller manner. Read my post here, https://www.the12volt.com/installbay/forum_posts.asp~TID~110320~get~last a burnt trace is a foil conductor on the circuit board that blows just like the element in a fuse.
Posted By: wass0026
Date Posted: January 10, 2009 at 3:39 PM
Lucky for me, the next day the lights began working again. He hasn't had a problem since. The Audiovox color listing for the 09 Econoline is still wrong. If you look at a tech sheet for the 08 Ford Expedition(I believe that was the one), it has pretty close to a match of the new Econoline's wiring.
Posted By: myinstallguy
Date Posted: January 10, 2009 at 7:53 PM
'09 Econoline should have a PURPLE / white in the drivers kick for p. lights. +. If anyone finds it please confirm.
-------------
*Installer since '89*
Posted By: myinstallguy
Date Posted: January 10, 2009 at 8:38 PM
Kassdog, I did some research. Let us know if the rest of this makes sense. Domelight (alarm trigger (In drivers kick)) = gray/violet + / Dome supervision (on when disarmed) GREEN/ blue @ dimmer switch. lock = gray / YELLOW - / unlock = violet/gray - (in drivers kick) Ignition wires (at switch): 12v constant = blue/red x 2, Ignition 1 = ORANGE / white, 1st Acc = PURPLE / green, 2nd Acc = BROWN / yellow, Starter = blue/white, Horn = blue/white (neg @ column), Brake = violet/white (@ switch), P.lights = violet/grey (drivers kick). Also, Econolines should now be equipped with "smart start", no tach wire needed. Vans ECM knows when to disengage starter, so vehicle will not grind starter (built in anti-grind). You can go tachless with a longer crank time. Please test to varify. This is second hand info. ------------- *Installer since '89*
Posted By: loneranger
Date Posted: January 10, 2009 at 9:08 PM
That anit-grind is a pretty nifty option for OEM.
-------------
Ideal - cmon dude, add to topics in a useful manner, not stuff that is obvious.
Story - Phzzzt! Hey, what happened?! ... Isn't it obvious?
Moral - Never dismiss the obvious.
Posted By: wass0026
Date Posted: January 18, 2009 at 7:52 PM
Everything sounds right on your wire colors myinstallguy, did you find those from a tech source or are those from just probing around? If you found them from a tech source I would be interested in knowing through who. I have found no sites with the correct information for that van.
Posted By: myinstallguy
Date Posted: January 20, 2009 at 9:20 AM
I've been working with the Gen 1 & 2 Ford products for years. I have good ties with some Ford dealers and between thier schematics and probing, I try to stay up to date. I know there are a few more changes for some 09 Fords in the works (or already in production), like the F-150. I'm going to survey one of them this week. Let me know if you want me to post what I find. ------------- *Installer since '89*
|