remote start and starter kill
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=118759
Printed Date: June 15, 2024 at 5:03 PM
Topic: remote start and starter kill
Posted By: tegguy
Subject: remote start and starter kill
Date Posted: December 23, 2009 at 1:26 AM
Ok I have a question I am sure has been covered but I am having a hard time picturing how to wire it. I have a 1992 Acura Integra 5 speed I have a Viper 5901 and plan to use the remote start but also want the starter kill. How do I wire this?
Replies:
Posted By: tedmond
Date Posted: December 23, 2009 at 7:27 AM
the thing ism even if you have a starter kill on the integra, the car can still be push started. If you want some sort of theft deterrant, your better off doing an ignition kill, but if that relay does die out on you while your driving, that can cause some serious problems. but this will work for start or ignition kill. take a relay
85 - ground when armed from alarm/rs
86 - ignition
cut ignition or start wire in half
87a - ignition or start wire (key side)
30 - ignition or start wire (car side)
Posted By: tegguy
Date Posted: December 23, 2009 at 3:14 PM
So how do you wire this with a remote start? Do I just wire the starter output and input to bypass this relay?
Posted By: tedmond
Date Posted: December 23, 2009 at 4:55 PM
if you hook up the starter output, it will act as an anti-grind for the starter wire. Other than that you wont be using that wire for this purpose. What you want to look for is the GROUND WHEN ARMED (locked) wire. in your install guide it might show up as anti-grin/ground when armed output. I dont touch dei stuff that often, i did a 871xv, and the wire colour was ORANGE / BLACK.
Posted By: tedmond
Date Posted: December 23, 2009 at 4:59 PM
however, i am not sure if the new modules still use the xcrs relay packs that have a starter kill built in.
Posted By: tegguy
Date Posted: December 23, 2009 at 6:05 PM
Let me see if I can make this question easier: | 85 | Orange on Alarm (Ground when armed) | | | | | | | 86 | Pink on Alarm (Ignition) | | | BLACK / YELLOW from car | | | 87 | NOT USED | | | | | | | | | 87a | Green on Alarm (starter input) | | | BLACK/ White switch side | CUT THIS WIRE IN 1/2 | | 30 | Violet on Alarm (starter output) | | BLACK/ White car side | CUT THIS WIRE IN 1/2 |
Is this what it will look like so I will have 2 wires to 86/87A/30 instead of just one or am I making this too complicated?
Posted By: tedmond
Date Posted: December 23, 2009 at 6:39 PM
hey, no need for the relay, since the unit does it for you. just cut the start wire in half. connect VIOLET to the end thats going towards the engine and connect the green to the wire towards the ignition cylinder. now you have a starter kill/antigrind built in. no need for the additional relay
Posted By: tegguy
Date Posted: December 23, 2009 at 6:58 PM
Hey thanks for the information. The manual confused me since it said car side of starter kill but you cleared it up
Posted By: howie ll
Date Posted: December 24, 2009 at 2:38 AM
If you read the manual you would see that there's already a built in starter/anti-grind cut, green and violet are the key side and starter side outputs. Follow Tedmund's advice, especially about ignition failure, he is very good.
Posted By: tedmond
Date Posted: December 24, 2009 at 5:45 AM
thanks for the comment howie, if i was very good i would have the symbol (i) for providing very accurate information ahah
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: tegguy
Date Posted: December 24, 2009 at 3:36 PM
howie ll wrote:
If you read the manual you would see that there's already a built in starter/anti-grind cut, green and violet are the key side and starter side outputs. Follow Tedmund's advice, especially about ignition failure, he is very good.
Sorry all I have at this time is the instillation manual and I didn't see anything in there where it mentioned it had a built in starter kill
|