remote start not working

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=118852
Printed Date: June 15, 2024 at 4:10 PM

Topic: remote start not working

Posted By: negokay
Subject: remote start not working
Date Posted: December 27, 2009 at 11:15 AM

I am trying to install a viper 5101 on a 2003 ford explorer with EXPRESSKIT PKALL DATA IMMOBILIZER. Whenever i try to remote start it i can hear it clicking, but dont start it.. I DONT KNOW WHERE I MADE THE MISTAKE.. PLEASE HELP....

I installed the followings

primary harness(h1) 12 pin

h1/1 CONNECT TO THE UNLOCK

h1/2 CONNECT TO YELLOW BATTERY

h1/3 CONNECT AT YELLOW/LTGREENN

h1/4 NOT CONNECTED

h1/5 GROUND @DRIVER KIK PANEL

h1/6 NOT CONNECTED

h1/7 NOT CONNECTED

h1/8NOT CONNECTED

h1/9NOT CONNECTED

h1/10 GROUNDED @ KIK PANEL

h1/11 HEADLIGHT BROWN

h1/12 NOT CONNECTED

(H2), 7 PIN CONNETOR

NONE CONNECTED

HEAVY GAUGE REMOTE START (H3) 8 PIN

H3/1 PINK TO RED / LT GREEN

H3/2 RED / WHITE +fused(30a) ignition 2 NOT CONNECTED

H3/3 ORANHE CONNECTED TO GREEN/ LT GREEN

H3/4 VIOLET:STARTER OUT CONNECTED TO RED

H3/5 RED CONNECTED TO YELLOW BATTERY

H3/6 N C

H3/7 N C

H3/8 CONNECTED TO YELLOW BATTERY

REMOTE START INPUT, 5-PIN

1- BLACK/ WHITE GROUND @ KIK PANEL

2- VIOLET/WHITE TACH @ COIL IN BLUE/LTGREEN

3- BROWN @ BRAKE PEDAL

4- HOOD PIN

5- N C

REMOTE START AUXILIARY OUTPUT, 5 PIN

THE ONLY ONE THATS CONNECTED IS THE BLUE STATUS OUTPUT AND ITS CONNECTED TO THE blue/white @ the pkall

ps: pkall is connected as d2d

PINK WIRE TO IGNITION RED / LTGREEN

BLACK N C

GREEN N C

TX TO WHITE/ LTGREEN

RX TO BROWN / LT ORANGE

-------------
yeyo

Replies:

Posted By: t&t tech
Date Posted: December 27, 2009 at 11:36 AM

Try inserting the key in the barrel and leave in the off position, remote start and see what happens!

-------------
COMMIT YOUR WAY TO JEHOVAH AND HE WILL ACT IN YOUR BEHALF. PSALMS 37:5

Posted By: negokay
Date Posted: December 27, 2009 at 1:49 PM

still not working ..

-------------
yeyo

Posted By: tedmond
Date Posted: December 27, 2009 at 1:57 PM

just a note, dont use the d2d, use it w2w method. make sure your powering up all ignitions and accessories. you might have tagged the wrong start wire, and the clicking is comming from the relays inside the rs.

-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert

Posted By: dasbogie
Date Posted: December 27, 2009 at 2:09 PM

Did you switch it to auto transmission mode. Its the first feature in the last menu. What type of tach signal are you running, virtual tach, voltage, or regular tach?

Posted By: negokay
Date Posted: December 27, 2009 at 2:22 PM

dont know how to do the w2w method and yes the clickin is coming from the rs

-------------
yeyo

Posted By: negokay
Date Posted: December 27, 2009 at 2:33 PM

how do you put it for auto trans and i connected the tach to the coil line.. do know which that is...

-------------
yeyo

Posted By: tedmond
Date Posted: December 27, 2009 at 2:37 PM

you have to go into the programming menu and look for that feature. For some reason i have a feeling you dont have the start wire connected. The start wire is purple comming off the xcrs relay pack.

-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert

Posted By: negokay
Date Posted: December 27, 2009 at 2:58 PM

it is connected its going to the RED wire in the ignision

-------------
yeyo

Posted By: negokay
Date Posted: December 27, 2009 at 4:19 PM

i've done the auto programin and its still not workin.. is there another wire biside the red wire in the ignition thats for the starter???

-------------
yeyo

Posted By: JWorm
Date Posted: December 27, 2009 at 4:25 PM

Connect H3/2 RED / white to constant 12v in the ignition harness.

Posted By: negokay
Date Posted: December 27, 2009 at 4:34 PM

i did that and its still not working..

-------------
yeyo