1989 civic 5901 viper
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=122058
Printed Date: May 15, 2024 at 9:35 AM
Topic: 1989 civic 5901 viper
Posted By: kawijess
Subject: 1989 civic 5901 viper
Date Posted: May 30, 2010 at 3:32 PM
Hi All. I think I might have screwed the pooch with this one. I managed to install one of these on my 06 silverado and I though I'd help install one on my brothers car. It was working fine and I was trying to get the rs installed. I connected the last wire which was the H2/18 blk/wht to the green red e-brake wire and then is when I smelled something. Now the remote won't work and the command center light does nothing. The running lights are on constantly and nothing else works. I think I might have burned out the brain. Looks like I'm going to have to buy a new one for him. Do they sell just the brain? What did I do wrong? Thanks for you help
H1/2__Red___________12VDC Constant Input__________________Grey Output from Backup Battery Diode Isolated
H1/3__Brown_________Siren Output__________________________Red Wire on Siren
H1/5__Black__________Chassis Ground________________________Ground
H1/7__Blue___________Trunk Pin/Instant Trigger Input___________blue from dash
H1/8__Green__________(-) Door Trigger Input__________________ GREEN/ red
H1/9__BLACK/ White_____200mA Dome Light Supervision Output_____WHITE/ blue
H1/11_White__________Parking Light Output____________________ RED / blk
H2 HARNESS
H2/9__Violet/White_____Tachometer Input______________________ blue from dash
H2/15_Grey___________Hood Pin Input________________________ hood pin and grey from BUB diode isolated
H2/17_Brown__________Brake Shutdown Input__________________ green white from foot brake
H2/18_BLACK/ White_____Neutral Safety Input____________________ green red from e-brake
H3 HARNESS
H3/1__Pink___________Ignition 1 Input/Output__________________ Black / YELLOW
H3/2__RED / White______Flex Relay 12v constant
H3/3__Orange_________Accessory Output______________________blue/white
H3/4__Violet__________Starter Output (Car Side)________________ BLACK/ white
H3/5__Green__________Starter Input (Key Side)_________________ BLACK/ white
H3/6__Red____________Ignition 1 Input 12v constant
H3/9__RED / Black_______Accessory/Starter Relay Input 12v conatant
Replies:
Posted By: howie ll
Date Posted: May 31, 2010 at 2:23 AM
The first thing I noticed was your black white dome supervision, should have joined it to H1/8 green.Also your constant at H1/12 red should have been diode split to a constant 12v+ feed as well.
Posted By: kawijess
Date Posted: May 31, 2010 at 11:36 AM
Thanks Howie II. I'm going to try that in a bit.
Posted By: kawijess
Date Posted: June 01, 2010 at 9:02 PM
I tried it. But still the same.
It looks like the running lights stay on. The acc is on and if i push the clutch in, it starts. Pushing any of the buttons on the decoder does nothing. Command center light does not come on at all nor does pushing/holding the button do anything.
Posted By: kawijess
Date Posted: November 27, 2010 at 12:07 PM
I got a new one so I'm going to try this again.
So the h1/green will have the h1/black white dome and the - door trigger and the white: blue wire all connected together?
The h1/12 should have a constant 12v feed going to it as well as the grey wire from battery backup?
Thanks so much for your help!!!
Posted By: howie ll
Date Posted: November 27, 2010 at 1:11 PM
H1/8 green and H1/9 black white join both to the GREEN/ red NOT the WHITE/ blue.
H1/7 Blue trunk trigger where does this go to on the dash? I hope it's the wire that goes to ground when the trunk is opened, should also be in the vicinity of the fuse box, at least that's where it is on British/Japanese R/hand drive versions.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: kawijess
Date Posted: December 04, 2010 at 4:52 PM
Do the H1/8 green and H1/9 black white need to be diode isolated?
I put the blue wire behind the dash. It's the one that turns on the the dash light got the trunk. I can relocate by the fuse box.
Posted By: kawijess
Date Posted: December 04, 2010 at 4:54 PM
Do the H1/8 green and H1/9 black white need to be diode isolated?
I put the blue wire behind the dash. It's the one that turns on the the dash light got the trunk. I can relocate by the fuse box.
Posted By: howie ll
Date Posted: December 04, 2010 at 5:59 PM
Your blue is correct, other two don't need diode isolating.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: kawijess
Date Posted: December 04, 2010 at 8:55 PM
Sorry about the spelling, I wrote it on my phone. Thank you so much for your help! It's working!
Posted By: howie ll
Date Posted: December 05, 2010 at 2:41 AM
I think I made a slight error, if your dome light supervision is working, fine if not H1/9 Black white goes through a relay (to boost its 200ma current output) as follows:
BLACK/ white H1/9 to 85.
Constant 12V+ 5amp fused to 86.
Good ground to 30.
Join to H1/8 green at 87.
1N4004 diode across 85 and 86, band towards 86.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: kawijess
Date Posted: December 05, 2010 at 8:17 AM
I'll check to see if it is working. If not, it's ok. I don't need it that bad.
Can you verify that these connections are ok? I'm not to sure on the H3/1 and H3/6.
H3 HARNESS
H3/1__Pink___________Ignition 1 Input/Output__________________ Black / YELLOW
H3/2__RED / White______Flex Relay 12v constant
H3/3__Orange_________Accessory Output______________________blue/white
H3/4__Violet__________Starter Output (Car Side)________________ BLACK/ white
H3/5__Green__________Starter Input (Key Side)_________________ BLACK/ white
H3/6__Red____________Ignition 1 Input 12v constant
H3/9__RED / Black_______Accessory/Starter Relay Input 12v conatant
Thanks again. Let me know if you have a paypal.
Posted By: howie ll
Date Posted: December 05, 2010 at 10:10 AM
You are absolutely correct in your last post.
Don't be daft, you're 5000 miles too far away to worry about "taking the food from my mouth"  ------------- Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: kawijess
Date Posted: December 06, 2010 at 12:08 AM
Well, I just wanted to send you a "gift" for all your help. I really appreciate it.
|