Print Page | Close Window

python 991, 574, 2010 wrangler

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=129325
Printed Date: October 31, 2024 at 6:08 PM


Topic: python 991, 574, 2010 wrangler

Posted By: 507 w
Subject: python 991, 574, 2010 wrangler
Date Posted: November 21, 2011 at 6:47 PM

Hello,  I have a python 991.  This morning I remote started and can't shutdown the engine, even with my key removed, pressed the brake, or open the hood.  The only way was disconnecting the the remote from the battery.  But when I tried to reconnect the power source, it started up the vehicle and stay on.  Also, I can't use the button on the control center.  Is there any way to physically reset the remote starter? thanks.



-------------
The Broken Link



Replies:

Posted By: smokeman1
Date Posted: November 21, 2011 at 7:14 PM
Did you install it?  If so, pull the fuses from the heavy gauge wires and the H1 harness if it also has a fuse.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation




Posted By: 507 w
Date Posted: November 21, 2011 at 7:31 PM

Yes, I pulled out all the fuses.  Also, pulled out the whole unit and the bypass.  I reconnected it back earlier without the bypass and nothing happened until I put in the key (without turning), the lights turn and everything, like it about to start.  I'll leave the unit out over night and hope the starter will discharge (if anything in there) and reset itself.  And yes, I read the instruction posted_image

Thanks



-------------
The Broken Link




Posted By: smokeman1
Date Posted: November 21, 2011 at 7:44 PM

What year, make and model of vehicle is it installed in?  And what model of Bypass?

And what wires from the Python are connected to what on the vehicle.

Thanks



-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation




Posted By: 507 w
Date Posted: November 21, 2011 at 8:33 PM

I got a Wrangler unlimited 2010

Bypass and firmware

DB-ALL- 401.CHRYSLER v3.10
http://www.xpresskit.com/VehicleCompatibility.aspx?p=null&year=2010&make=Jeep&model=Wrangler%20Unlimited&ps=1&s=0

I connected everything in the diagram installation-Type 3

Beside the yellow/black RAP off - from the bypass ---- Don't know what it is and the starter worked for for week without it

and the handbreak status input --- I connected to the ground (didn't work when I connected to bypass)

My starter might have burnt out

Thank You. 



-------------
The Broken Link




Posted By: 507 w
Date Posted: November 22, 2011 at 12:04 PM

Can somone tells me what the yellow/black RAP off is for? 

Thanks 



-------------
The Broken Link




Posted By: awdeclipse
Date Posted: November 22, 2011 at 12:52 PM
It is to "simulate" opening the door when the remote start shuts down to turn off the accessories. R.etained A.ccessory P.ower




Posted By: 507 w
Date Posted: December 13, 2011 at 9:57 AM

Thank You for answering my previous questions.  I ran in another proplem.  My OEM security cannot be arm or disarm with my after market remote.  Please help.

thanks



-------------
The Broken Link




Posted By: 507 w
Date Posted: January 09, 2012 at 4:56 PM

Someone please tell me how to hook up to disarm my 2010 Jeep Wrangler OEM alarm?  I'm using the python model 574 with DBALL bypass.   I can't use the DBALL to disarm the OEM alarm.  how can I wire to wire it.  Thanks



-------------
The Broken Link




Posted By: offroadzj
Date Posted: January 09, 2012 at 5:10 PM
The factory disarm can only be controlled through the factory remote. There is no way to hardwire it as it is all data controlled. The DB-ALL should control the factory arm/disarm. Do you have it connected D2D or W2W? You may have a bad bypass. If so I would recommend going with an idatalink or Fortin bypass. They seem to be more reliable.
Idatalink bypasses:
ADS-ALSL CH or ADS-DLSL CA2
Fortin Bypass:
Evo-CHR (be sure to have it pre-flashed with the correct firmware).
You can also pick up the THAR-CHR2 T-harness which makes it a 10minute install... makes life extremely easy.

-------------
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205




Posted By: 507 w
Date Posted: January 09, 2012 at 5:54 PM
Thank You very much

-------------
The Broken Link





Print Page | Close Window