viper 350, 2013 ford f-250

Can anyone help me by telling me EXACTLY what wires to hook where, including relays etc.. to get the dome light supervision, and what wire for the door trigger is on this truck. Its a Viper 350plus and a 2013 F-250 Super Duty

No one can help in the way you want but these comments from other members might steer you correctly:-
If you can, post up the wire connections from the Viper install manual. That will at least give us a head start to help you link the 2 diagrams together. A lot of us tend to be busy and as much as we love to help, we don't always have time to search for the manual and then make up a complete write-up for wire to wire connections. But if you can get us at least half way there, it will save us time.

Use this format:

Connector 1:
Pin (if available) - Wire Color - Wire description (i.e. ignition, status out, etc)
Copyright offroadjz 2013

Here are a few resources for wiring...
The 12 Volt : https://www.the12volt.com/installbay/vehicles.html
Bulldog Security : https://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.asp
Audiovox : https://techservices.audiovox.com/AccessRequest.aspx    Requires free sign-up.
DEI : https://www.readyremote.com/main.asp
Copyright Kregg 2013


-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.

And we will never be able to tell you EXACTLY. Although most of the wiring information even we can get is usually accurate, it isn't perfect... especially with newer vehicles. So no matter what, you will always have to test and verify every wire before connecting anything. In addition, that truck should have factory domelight supervision and a connection most likely isn't necessary.

Here is the information for the door trigger. It is a N.C. wire so you will need to set the unit for N.C. (if it has the ability).
Door Trigger      GREEN/ purple      - N.C.      BCM in passenger kick, black 26 pin plug (C), pin 9

Here is the information for the domelight if you choose to connect it:
Dome Supervision      gray/purple (dome lamp); purple (puddle lamp)      +      BCM, gray 12 pin plug (A), pin 1; black 26 pin plug (C), pin 1

-------------
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205

For dome supervision I.e. the domelight to come on when you nlock the doors hook the BLACK/ white wire from the alarm to the gray/purple wire at the puddle lamp. USE A RELAY. The BLACK/ white from the alarm is a negative output and the signal to the gray/purple needs to be positive.

Regarding the n/c door trigger your alarm is NOT programmable for this. So yiu woukd Need relays to use the actual door trigger although you can also use the domelight wire as your trigger to the purple wire on your alarm as the light comes on when ANY of your doors are opened.

Also if you truck has the factory alarm yiu can only disarm the factory alarm with the factory remote or losing a key and using a 556 module and output to the ignition. In this case if yiu just wanted an alarm I would recommend using a viper 350hv as a factiry add on using your factory remote instead. Which also woukd help for the next special part about yiur truck.

Wich Is that yiu also need to test if your door locks shut down. On some ford trucks like yours the bcm shuts down so that the doors can nit be unlocked from the switch or an after market alarm unless you trigger a door trigger first to wake up the system.

Good luck. :)

-------------
Gary Sather

And I apologize for my horrible spelling. My iPad keyboard is horrible. :)

-------------
Gary Sather

I know that one, I've abandoned plans to take a tablet to work, I will be using a laptop instead.

-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.