2013 rdx w/ push button vs viper 5704

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=134873
Printed Date: May 23, 2024 at 3:27 AM

Topic: 2013 rdx w/ push button vs viper 5704

Posted By: BChillin83
Subject: 2013 rdx w/ push button vs viper 5704
Date Posted: September 14, 2013 at 3:25 PM

Hey guys, its been a real long time since I did a remote start install and just need a little help since I am pretty rusty. I have also never done a vehicle with push button start. Can you guys tell me if I got this right?

RDX wires are on the left. 5704 wires are on the right

posted_image

12 volts = white      -----      red and RED / white
second 12 volts = NA     -----      NA
starter = gray -----      violet car side and green key side
second starter = brown     -----     NA
ignition = blue -----     pink
second ignition = red     -----     pink/white
third ignition = NA     -----     NA
accessory = orange     -----     orange
second accessory = purple ---     RED / black
third accessory = NA     -----     NA

pink/black of 5704 is not used

Replies:

Posted By: triniforever
Date Posted: September 14, 2013 at 5:36 PM

It would probably be a good idea to use a flash module that handles everything through data for remote starting and keyless entry ,and alarm but I don't think secure takeover is available on this vehicle . Idatalink CA maybe ? The install looks pretty straightforward .

-------------
triniforever

Posted By: BChillin83
Date Posted: September 15, 2013 at 2:02 AM

yea I am going to use a flash module but was just getting the H3 harness out of the way

Posted By: triniforever
Date Posted: September 15, 2013 at 11:56 AM

The Red ,RED / Black and RED / White wires are 12v input and needs to be connected to a 12v source like the White wire from the power control unit. The second accessory wire in the car (Purple) while it may not be necessary to be connected but if you have to on the H2 harness on the 5704 (H2/22) it's an Orange wire (-) 200 mA accessory output , you can use this with a relay to power the second accessory wire.

-------------
triniforever

Posted By: lucasoil4u
Date Posted: September 17, 2013 at 12:05 PM

Car will die when you open the door. Just did one last week. Use a ADS AL CA

Posted By: BChillin83
Date Posted: October 03, 2013 at 3:57 PM

5704 is installed on 2013 RDX with push start. An FLCAN was used.

Is it normal for the car to unlock when remote start is used?

1. Car is locked and system is armed.
2. I remote start, doors unlock but system stays armed
3. I turn off remote start and the doors lock back, system remains armed.

All while factory key fob is nowhere near the proximity of the car

How do I get the doors to stay locked while remote start is engaged?

Posted By: BChillin83
Date Posted: October 23, 2013 at 12:19 PM

BChillin83 wrote:

5704 is installed on 2013 RDX with push start. An FLCAN was used.

Is it normal for the car to unlock when remote start is used?

1. Car is locked and system is armed.
2. I remote start, doors unlock but system stays armed
3. I turn off remote start and the doors lock back, system remains armed.

All while factory key fob is nowhere near the proximity of the car

How do I get the doors to stay locked while remote start is engaged?

Bump, Anyone?

Posted By: tedmond
Date Posted: October 23, 2013 at 12:24 PM

depends on the remote start, some tell the bypass to unlock, start, restart. you might want to double check programming.

go into the unit settings and set it to lock after start.

-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert

Posted By: BChillin83
Date Posted: October 23, 2013 at 4:55 PM

I got it working. I totally overlooked the setting on the remote start menu. I also think that my factory key fob was too close to the vehicle to make sure it was working correctly.

Thanks!