heater does not come on after remote start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=134915
Printed Date: April 28, 2024 at 12:35 AM
Topic: heater does not come on after remote start
Posted By: namyenruoj
Subject: heater does not come on after remote start
Date Posted: September 22, 2013 at 1:45 PM
hello,
just bought a viper 5904V installed everything including remote start but some how my heater on my 1991 toyota celica does not come on once you take the key off the ignition. need help how to make this work thank you
-------------
Replies:
Posted By: triniforever
Date Posted: September 22, 2013 at 2:28 PM
On the ignition switch harness from the car you will find a Grey wire this is your Accessory wire that controls the heater and other stuff , this wire needs to be connected to the Orange wire from the Alarm"s ignition harness.
-------------
triniforever
Posted By: triniforever
Date Posted: September 22, 2013 at 2:34 PM
Probably a good idea to post what wires from the alarm you connected to what wires in the car!&
-------------
triniforever
Posted By: namyenruoj
Date Posted: September 25, 2013 at 2:21 AM
Remote Start, 10-pin heavy gauge connector
Alarm Harness Description Car Harness
Pink + ignition 1 input/output BLACK/ Orange
RED / White + fused (30A) ignition 2/flex relay input 87 constant
Orange+ accessory output grey
Violet + starter output car side of the starter kill blk/wht
Green + starter input key side of the starter kill blk/wht
Red + fused 30A ignition 1 input constant
Pink/White + ignition 2/ flex relay output didn't use don't know
Pink/Black + flex relay input 87a key side didn't use don't know
RED / Black + fused 30A accessory/starter input constant
NC no connection
I also notice when i do my remote start once you take out the key off the ignition my battery icon from the dash board comes on. if you started the car remotely the battery icon from the dash board also comes on and after you turn the ignition with the key in it the battery icon comes off. i don't have this problem when i did my 1998 rav 4 with viper 5701 with a remote start as well.
Main Harness, 6-pin connector
Red + 12vDC constant input yes
Black - chassis groundyes
Brown + siren output yes
WHITE/ Brown parking light isolation wire didn't use don't know
Whiteparking light output yes
Orange - ground when armed output no
Door Lock, 3-pin connector
Blue- unlock output yes
Green - lock output yes
Auxiliary/Shutdown/Trigger Harness
Pink/White - ignition 2/flex output no
Blue/White - 2nd status/rear defogger output didn't use don't know
RED / White trunk release no
BLACK / YELLOW dome light output yes
Dark Blue status output i used this to by pass my clutch
WHITE/ Black don't know
WHITE/ Violet don't know
ORANGE / Black don't know
Gray hood pin input yes
Blue trunk pin/instant trigger input no
WHITE/ Blue activation input don't know
Violet/White tachometer input tied in from black wire igniter
BLACK/ White - parking brake inputyes
GREEN/ Black - factory alarm disarm output didn't use don't know
Green door input yes
BROWN / Black - horn honk output i would like to use this don't know
Pink - ignition 1 output no
Violet + door input no
Violet/Black - aux 2 output no
Brown + brake shutdown input yes
Violet / YELLOW - starter output didn't use don't know
Gray/Black - diesel wait to start input didn't use don't know
Orange - accessory output didn't use don't know
GREEN / WHITE - factory alarm arm output didn't use don't know
please i need your help
-------------
Posted By: kreg357
Date Posted: September 25, 2013 at 4:23 AM
Alarm Harness Description Car Harness
Pink + ignition 1 input/output BLACK/ Orange
RED / White + fused (30A) ignition 2/flex relay input 87 constant
Orange + accessory output grey
Violet + starter output car side of the starter kill blk/wht
Green + starter input key side of the starter kill blk/wht
Red + fused 30A ignition 1 input constant
Pink/White + ignition 2/ flex relay output Blue/Red ***Set to IGN2 - default
Pink/Black + flex relay input 87a key side not used
RED / Black + fused 30A accessory/starter input constant
NC no connection
-------------
Soldering is fun!
Posted By: namyenruoj
Date Posted: September 25, 2013 at 2:10 PM
kreg when you say set to ignition 2. where is ignition 2 (blue/red)actually is. is this why my dash board light does not come on?
is this also the reason why my dome light does not come on when you arm/disarm, remote starts? i will try this out and i will let you know. thanks for the help
-------------
Posted By: kreg357
Date Posted: September 25, 2013 at 3:59 PM
The Blue/Red wire should be another wire in the main ignition switch harness, where you found the other ignition wires. As always, test for it with your DMM and make quality solder connections.  ------------- Soldering is fun!
Posted By: namyenruoj
Date Posted: September 27, 2013 at 7:02 PM
thanks Kreg i got it. i still want to make my dome light to come on when dis arming the system. it says in the manula to use the BLACK / YELLOW from the 24-pin but when i connected this to my RED / White car harness for my dome light it does not work properly my dome light is dim. when i meter the wire -12volts constant. don't understand why? i also want to make my defroster to work if it's possible
-------------
Posted By: namyenruoj
Date Posted: March 25, 2015 at 12:27 AM
still confuse. still can not make my dome light to work for my 1991 celica with viper 5904v. i need help please
my transponder led does not blink as well but a have a dim constant blue light on my tranponder antenna. everything works i wonder why?
-------------
Posted By: howie ll
Date Posted: March 25, 2015 at 2:02 AM
You might have a bad ground. Check the voltage between your ground point and any of the fuses.
Or, you're in valet mode.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: tedmond
Date Posted: March 25, 2015 at 9:03 AM
the domelight supervision output is limited to 250ma, whereas the dome light in the car draws well over an amp easily. Since its a tungsten filament in the bulb it can still be lit with 250ma and not draw the max current.
use a relay to increase the current on the domelight output.
85 - domelight output from unit
86 - constant 12v fused
87 - chassis ground
30 - dome light wire in car.
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: namyenruoj
Date Posted: March 25, 2015 at 7:04 PM
it's telling me to use BLACK / YELLOW from the 5904v harness but i that wire is positive?
-------------
Posted By: tedmond
Date Posted: March 25, 2015 at 7:17 PM
the wire is negative
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
|