Print Page | Close Window

avital 5303 heavy gauge wiring colors

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=136102
Printed Date: October 31, 2024 at 6:29 PM


Topic: avital 5303 heavy gauge wiring colors

Posted By: jnz1
Subject: avital 5303 heavy gauge wiring colors
Date Posted: February 19, 2014 at 5:38 PM

Has anyone else ran into the heavy gauge wiring not matching the instructions. It seems the first four wires match, but the last four are switched around. Mine are Purple, green, fused red, orange, Fused red, pink, fused red, pink/White



Replies:

Posted By: jnz1
Date Posted: February 19, 2014 at 5:56 PM
The instructions are showing a 7 pin plug and the plug provided has 8 pins




Posted By: jnz1
Date Posted: February 20, 2014 at 3:31 AM
500m xcrs is printed on the relay box.




Posted By: smokeman1
Date Posted: February 20, 2014 at 5:43 AM
What instructions are you referring to? Viper 571?, Avital?

I think you are asking about the heavy gauge harness. The 7 pin connector is the ribbon cable that goes from the remote start unit to the xcrs.

Compare the wiring diagrams from the Viper 571 and an Avital 5303. You will see there is a bit of wiring difference.
And I believe your 7th wire listed (fused red) is probably a fused RED / white.

The Viper 571 install manual is located in the downloads section of this site.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation




Posted By: jnz1
Date Posted: February 20, 2014 at 11:51 AM
It's the avital 5303. In the instructions it list the heavy gauge as a 7 pin. The wiring has 3 fused inputs vs the directions also shoeing two.




Posted By: jnz1
Date Posted: February 20, 2014 at 2:43 PM
The 571 wiring matches the wiring I received with the avital 5303. Should I follow the directions for the 571?




Posted By: jnz1
Date Posted: February 20, 2014 at 3:49 PM
posted_image
posted_image

Instructions from both the avital 5303 and the Viper 571




Posted By: smokeman1
Date Posted: February 20, 2014 at 4:07 PM
You should follow the instructions for the system you have. HOWEVER, you need to have the correct parts/pieces. It would appear that you have the wrong harness.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation




Posted By: jnz1
Date Posted: February 20, 2014 at 4:18 PM
To finish I could probably switch a few of the wires around so I have the fused inputs in the right spot. Right?




Posted By: smokeman1
Date Posted: February 20, 2014 at 6:56 PM
If you are confident with what you are doing.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation




Posted By: jnz1
Date Posted: February 20, 2014 at 7:02 PM
Is there a certain brain that goes with the Avitsl 5303? Is it possible I got a different brain that goes with this harness?




Posted By: jnz1
Date Posted: February 20, 2014 at 7:53 PM
The directed 5x03 brain was included. I'd hate to cut and solder the wires and find out I should have used the original wires with different install instructions.




Posted By: jnz1
Date Posted: February 21, 2014 at 3:05 AM
Also did a little research and the avital 5103 wiring colors match what I have. What's my best way to figure out what install to follow. Directed won't offer any help because I am not a dealer.




Posted By: smokeman1
Date Posted: February 21, 2014 at 7:02 AM
You'll have to ask the person that sold you the system, So you what you are working with.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation




Posted By: jnz1
Date Posted: February 21, 2014 at 7:16 PM
I was able to get some help from directed even though I wasn't a dealer and they provided the correct wiring diagram and the wiring is correct.





Print Page | Close Window