Printer Friendly Forum Posts - viper 5704 and dball on pts mazda 6

Hi
I installed a 5704 Viper and Dball using D2D in my 2009 Mazda 6 with push button start. This is the first time I'm doing such a work. I did electrical work before so I'm familiar with things, anyways the alarm part of the installation works doors, trunk, also, but the remote start would not work. There is no error code since the first two (safety switch ground, and switching to automatic from manual I eliminated. If I press the remote start the lights are flashing the doors are locking, and the remote says on and start counting down from 12 but the car would not start. I tried pressing the brake pedal then hit remote start and it works. I'm using Dball with firmware Mazda 1.10.14, any suggestions are greatly appreciated.
These are my connections:

Main Harness (H1), 6-pin connector

H1/1 RED (+)12VDC CONSTANT INPUT –Advanced keyless entry module orange – 6 pin connector

H1/2 BLACK (-) CHASSIS GROUND - ground

H1/3 BROWN (+) SIREN OUTPUT – not used

H1/4 WHITE/ BROWN PARKING LIGHT ISOLATION WIRE - PIN 87a of onboard relay – not used

H1/5 WHITE PARKING LIGHT OUTPUT - Advanced keyless entry module – orange blue – 9 pin connector

H1/6 ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT - not used

H2/1 PINK/WHITE (-) 200mA IGNITION/FLEX RELAY CONTROL OUTPUT

H2/2 BLACK/ WHITE (-) NEUTRAL SAFETY INPUT - Ground

H2/3 BLUE/WHITE (-) 200mA 2ND STATUS /REAR DEFOGGER OUTPUT

H2/4 GREEN/ BLACK (-) 200mA OEM ALARM DISARM OUTPUT

H2/5 RED / WHITE (-) 200mA TRUNK RELEASE OUTPUT – BCM -30 pin connector black red

H2/6 GREEN (-) DOOR TRIGGER INPUT (N/C* OR N/O)

H2/7 BLACK / YELLOW (-) 200mA DOME LIGHT SUPERVISION OUTPUT

H2/8 BROWN / BLACK (-) 200mA HORN HONK OUTPUT

H2/9 DARK BLUE (-) 200mA STATUS OUTPUT

H2/10 PINK (-) 200mA IGNITION 1 OUTPUT

H2/11 WHITE/ BLACK (-) 200mA AUX 3 OUTPUT

H2/12 VIOLET (+) DOOR TRIGGER INPUT

H2/13 WHITE/ VIOLET (-) 200mA AUX 1 OUTPUT

H2/14 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT

H2/15 ORANGE / BLACK (-) 200mA AUX 4 OUTPUT

H2/16 BROWN (+) BRAKE SHUTDOWN INPUT

H2/17 GREY (-) HOOD PIN INPUT (N/C OR N/O) – hood pin BCM

H2/18 VIOLET / YELLOW (-) 200mA STARTER OUTPUT

H2/19 BLUE (-) TRUNK PIN/ INSTANT TRIGGER INPUT (N/C OR N/O)

H2/20 GREY/BLACK (-) DIESEL WAIT TO START INPUT

H2/21 WHITE/ BLUE (-) REMOTE START/ TURBO TIMER ACTIVATION INPUT

H2/22 ORANGE (-) 200mA ACCESSORY OUTPUT

H2/23 VIOLET/WHITE TACHOMETER INPUT

H2/24 GREEN / WHITE (-) 200mA OEM ALARM ARM OUTPUT

Remote Start, (H3) 10-pin connector

H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT – Dball pink ign input + Dball gray/blk ign output

H3/2 RED / WHITE (87) FLEX RELAY +12V INPUT (30A FUSED) – do I need to connect?

H3/3 ORANGE (+) ACCESSORY OUTPUT

H3/4 VIOLET (+) STARTER OUTPUT (CAR SIDE OF THE STARTER KILL) - Advanced keyless entry module – 30pin connector brake wire RED / white

H3/5 GREEN (+) STARTER INPUT (KEY SIDE OF THE STARTER KILL)

H3/6 RED IGNITION 1 +12V INPUT (30A FUSED) – do I need to connect?

H3/7 PINK/WHITE (30) FLEX RELAY OUTPUT (car side of ign, acc or starter wire)

H3/8 PINK/BLACK (87a) FLEX RELAY INPUT (key side of ign, acc or starter wire if needed)

H3/9 RED / BLACK ACCESSORY/STARTER RELAY +12V INPUT (30A FUSED) – do I need to connect?

H3/10 NC No Connection

Dball wires: blk/white Scomm - Advanced keyless entry module – 30 pin connector BLACK/ red

GREEN/ blk - Advanced keyless entry module – 12pin – blk/red pts

Tan HSCAN low - Advanced keyless entry module – 12pin – blue/red CAN low

Tan/blk HSCAN high - Advanced keyless entry module – 12 pin gray /red CAN high

Yellow/blk TX - Advanced keyless entry module – 12pin gray/orange TX

ORANGE / blk RX + yellow red – Advanced keyless entry module 12pin WHITE/ green RX BCM side

ORANGE / red – Advanced keyless entry module 12 pin WHITE/ green keyport side