viper alarm 5704v into 96 integra

I have a viper alarm 5704v and im trying to install it into my 96 integra. I got the basic power ground and siren hooked up as well as the locks, now im having issues wiring up these,

h1/4 white w/brown parking light isolation wire? were does this go?
h1/5 white parking light output were does this go?
h1/6 orange (-)500mA ground when armed output, were does this go?

then also I attempted to wire up the remote start but on this alarm I got the heavy gauge 10 pin connector wire up but when I plug into the brain the alarm does arm or disarm or anything, but I also am having questions on were to wire up the 24 pin connector, I know like half of them aren't gonna be used here's a list of ones I need help with

h2/1 pink w/white- (-)200mA ignition/flex relay control output
h2/2 BLACK/ white (-) neutral safety input
h2/6 green (-) door trigger input (n/c or n/o)
h2/7 BLACK / YELLOW (-)200mA domelight supervision output
h2/9 dark blue (-)200mA status output
h2/10 pink (-)200mA ignition1 output
h2/12 (+) door trigger input
h2/16 brown (+)brake shutdown input
h2/18 violet / YELLOW (-)200mA starter output
h2/21 WHITE/ blue (-) remote start/turbotimer activation input
h2/22 orange (-)200mA accessory output

any help is very appreciated thanks

I wil help with what I can.

slammedcx wrote:

---

I have a viper alarm 5704v and im trying to install it into my 96 integra. I got the basic power ground and siren hooked up as well as the locks, now im having issues wiring up these,

h1/4 white w/brown parking light isolation wire? were does this go? Not needed for you application
h1/5 white parking light output were does this go? This is the parking light output and will hook to the wire that tests as either power 12v +ve when turning the parking lights on, or ground -ve when turning the parking lights on with the head light switch.
h1/6 orange (-)500mA ground when armed output, were does this go? This wire would control a start kill relay if you install one. Personal opinion is you do not need a starter kill relay but we can help if you wish to do it.

then also I attempted to wire up the remote start but on this alarm I got the heavy gauge 10 pin connector wire up but when I plug into the brain the alarm does arm or disarm or anything, but I also am having questions on were to wire up the 24 pin connector, I know like half of them aren't gonna be used here's a list of ones I need help with

h2/1 pink w/white- (-)200mA ignition/flex relay control output Should not be needed
h2/2 BLACK/ white (-) neutral safety input  Must be hooked to ground or ebrake (manual transmission) in order for the remote start to operate
h2/6 green (-) door trigger input (n/c or n/o) Connect to a negative door pin or domelight circuit. Also required on manual transmission. May need diodes for multiple door pins.
h2/7 BLACK / YELLOW (-)200mA domelight supervision output Hook to a door pin or domelight wire to allow for the domelight to turn on when you press unlock. For +ve domelight circuits or high current ground needs you will need to use a relay.
h2/9 dark blue (-)200mA status output  Can be used for either a bypass (interface) or defrost turn on
h2/10 pink (-)200mA ignition1 output  Should not be needed
h2/12 (+) door trigger input
h2/16 brown (+)brake shutdown input  Required for remote start shut down. Will attach to a wire that tests 12v +ve when the brake pedal is pressed.
h2/18 violet / YELLOW (-)200mA starter output Should not be needed
h2/21 WHITE/ blue (-) remote start/turbotimer activation input  Should not be needed
h2/22 orange (-)200mA accessory output  Should not be needed

any help is very appreciated thanks

---

-------------
To master and control electricity is perfection. *evil laugh*

thanks very much I really appreciate it ima give it a shot!!

Starter Kill/Anti-grind is built-in to the 5704v so it only needs to be correctly wired up, an external relay is not required.