remote starter, 2008 toyota rav4

HiAll

       I am looking to install viper875xv remote starter on my 2008 toyota rav4 sports 4 cylinders please guide me with the instructions and wiring diagramms,do i need bypass module and realy installation for this project.

  Thanks

Hi All,
      I am trying to install viper 875xv remote starter on my 2008 Toyota rav4,thanks to 12 volt forum where I got the diagrams I am having some concern with extreme capacity relay satellite do I really have to connect it with the starter or it is optional if I have to connect it then how it will be connected to the starter module please guide me.
              Thanks

Can you post the wiring layout for this Viper unit. I can't find a PDF file for it.
Unless someone out there has it to post or upload.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

Your Rav4 has two starters and two Ignitions which need to be addressed as well as one accessory.
Research this site for other info on RAV4 installs.

Below are a couple of sites for wiring guides:

https://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.aspx
https://www.commandocaralarms.com/wiringsearch.asp

These listings are "GUIDES" and may not reflect what your Rav4 has. You will still need to use a DMM to test and verify each wire for its function prior to making your connections.

You will also need to address the immobilizer system of your Rav4.
Do you have a bypass? Fortin Key-Override All, DB-ALL or ??
Take time to research to see what fits your needs. DB-All needs to be flashed for your vehicle. Idatalink ads-alca is another source.

I take it this is first time you are trying to install a remote starter. It is not a couple of hour job. Plan on a long weekend.
Might want to look at some Youtube video on remote starters.

To get you started:
Heavy Gauge Harness:
H/1 Purple to Starter 1,(Yellow+)
H/3, Red; H/5, Red; H/7 RED / White; and (from main harness) H1/2 Red, to 12volt, (Blue+)
H/4 Orange to Accessory, (Red+)
H/6 Pink to Ignition 1, (White+)
Starter 2 is listed as White also, MUST make sure you know which is which by testing with DMM.
H/7 Pink/White to Ignition 2,(Pink+)

Purple wire from Relay satellite 4 Pin connector to Pin 85 of a 30/40amp relay; Pin 87 and 86 to 12volts, pin 30 to Starter 2 (White+)
https://www.the12volt.com/relays/relays.asp

Blue wire from Relay satellite 4 Pin connector to your bypass module status wire.

H1/5 Black to chassis ground. H3/1 BLACK/ white to ground IF automatic trans.
H3/2 to Tach signal
H3/3 to Brake, (Blue+)
H3/4 to hood pin supplied with your remote starter kit. Important Safety Feature

Take your time. Test, Verify, Connect. One wire at a time. Good luck

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

Hi smokeman1,
This is so kind thanks a lot for your great help, as you instruct me I will test each wire, I also bought innowa smart test light to test the wire,I will also test these wires form DMM.
I have some concerns, just for remote starter I only have to use those wires which you marked or I also have to connect some wires from main harness H1, H4, door lock, H2 harness, I only want to install starter not the security.could you please explain me about door trigger zone 3 , what is the means for zone asking for knowledge purpose.
      Thanks

Hi All,
        I bought dball bypass module can I use d2d wire for remote starting because I only want remote starter option, or I have to connect dball wires to the remote starter module please advice me what should I do.
Thanks