python 4211p with immobilizer bypass wire
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=137576
Printed Date: April 27, 2024 at 4:26 AM
Topic: python 4211p with immobilizer bypass wire
Posted By: lopezchris21
Subject: python 4211p with immobilizer bypass wire
Date Posted: October 31, 2014 at 9:50 PM
Hello guys. I would like some confirmation on my wires before i jump into this. If anyone sees anything wrong please let me know. Also if there is a question mark next to it im not sure about it.
Thank you
Remote start - python 4211p with Dball2pro with XCRS (extreme capacity relay satellite)
Car - 2006 honda civic si
16 pin connector
pin 3 Immobilizer Data: ORANGE / Black to pin 3 on immobilizer plug
pin 6 single wire can Lt. green to pin 4 on immobilizer plug
pin 10 (-) lock output GREEN/ black to Pin 28 driver side kick panel (34 pin plug)
pin 13 (-) unlock output Lt. Blue/ black to Pin 27 driver side kick panel (34 pin plug)
XCRS plug
Violet + Starter output (starter side) to Cut yellow in half at ignition switch starter side
Green starter input (from key) to Cut yellow in half at ignition switch Key side
Red + 12 v input to BLue + Ignition switch
Orange Accessory output + to Orange + Igniton Switch
Red +12v input to BLue + Ignition switch
Pink + Ignition Output (also input to yellow wire in ribbon) to ???
RED / wht + Fused 30a ignition 2/ Flex relay input to NOT USED
Pink/ wht +ignition 2 / Flex relay output to NOT USED
18 pin connector
Pin 3 gray Hood input - to Hood pin on bay
Pin 8 BROWN / blk Horn - to Orange Fuse box rear 16 pin plug
pin 13 lt blue trunk input - to ??? Trunk release is green but + kick panel 42 pin plug
Pin 17 brown siren output + to NOT USED
12 pin connector
pin 1 &7 white Parking light output + to ???
Pin 2 &8 white / brown Parking light input + to ???
pin 9 black Ground - to Body
pin 10 red 12V + to BLue + Ignition switch
If i am missing anything please let me know.
Thanks
Replies:
Posted By: lopezchris21
Date Posted: November 03, 2014 at 12:31 AM
no one?
Where do the Flex wires go?
What about the light output/input?
Anything on Pink + Ignition Output (also input to yellow wire in ribbon) to ?.
Any help please
Posted By: bs1d3
Date Posted: November 03, 2014 at 5:02 PM
Red, Red and RED / White will all go to 12v (white) at the ignition switch.
Pink goes to ignition (blue) at the ignition switch.
Pink/White goes to 2nd ACC (red) at ignition switch. (Program to ACC in menu instead of IGN)
Trunk input is for an alarm or manual trans.
White will go to your + parking light wire (red @ fuse box, lt green plug pin 19)
WHITE/ brown goes to 12v (white) at ignition switch or tie it in to your other 12v wires.
Posted By: lopezchris21
Date Posted: November 03, 2014 at 5:13 PM
Thanks so much for your input. Question.
I want to trick it to think my car is auto. Will this wiring be the same?
Will I need the trunk when doing this?
Someone mentioned a neutral safety switch. Do I need that?
Thanks for your time.
Posted By: lopezchris21
Date Posted: November 03, 2014 at 5:14 PM
Also the very last red 12v on the pin 10, wood that also go to the white?
Posted By: smokeman1
Date Posted: November 04, 2014 at 6:54 AM
I want to trick it to think my car is auto.
Bad Move. If car is manual transmission.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: lopezchris21
Date Posted: November 04, 2014 at 7:32 AM
Why is it a bad move?
As long as im careful with not leaving it in gear, what can go wrong? I'm in and out of my car a lot and do not want to deal with the procedure of a manual.
|