soundstream tarantula
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=138715
Printed Date: April 28, 2024 at 4:35 AM
Topic: soundstream tarantula
Posted By: f29966
Subject: soundstream tarantula
Date Posted: March 24, 2015 at 12:49 PM
i'm installing the tarantula ars.2 on a toyota tacoma 2015 , the problem i'm facing is the tachless mode and the valet mode, everytime i program the system to tachless mode the remotestart working but i can't set the system to valet mode , valet mode working if i reset the system. any one know what wrong ?
Installation manual
Replies:
Posted By: howie ll
Date Posted: March 24, 2015 at 6:08 PM
Might be a bad ground, do a voltage test between your grounding point (preferably one of the many 10mm bolts under dash or around kick panel and your fuses.
Also make sure the green door trigger wire is correct, i.e. goes to ground when a door is opened.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: tedmond
Date Posted: March 24, 2015 at 6:40 PM
why are you running tachless, when the tach wire is right at the OBD? I'm sure you used a convenience module of some sort, which definitely would give you a tach signal.
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: howie ll
Date Posted: March 24, 2015 at 6:46 PM
Pin 9 at the OBD.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: f29966
Date Posted: March 25, 2015 at 4:03 PM
i reset the system to default and connect the tach wire on alarm to pin 9 at the OBD , then i start the car with the key i hear 2 chirps ,
the manual said 2 chirps = tach mode
3 chirps = data tach mode
4 chirps = tachless mode
i don't know what to do next after i hear 2 chirps . i tried to do remote start after i hear 2 chirps but it start the car for afew second and shutoff . i really don't understand the manual .
Posted By: howie ll
Date Posted: March 25, 2015 at 4:23 PM
Bypass required?
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: f29966
Date Posted: March 25, 2015 at 6:02 PM
i have it working now , after i program the tach to hybrid mode 1 , the remote start not shutoff any more and i also can set the system to valet mode , but i found a new problem with the starter-kill wire ( connect to kill switch relay ) , after arm the system with alarm remote , and i set the system to valet mode but the starter-kill wire still send out the ground so i can't start the car by key if the alarm remote broke or out of battery . maybe i connect the relay wrong or the system is defected. below is how i connect the kill switch relay to the starter wire
relay: 30 - motor side
87a- key side
85 - to ignition
86 - starter-kill wire from alarm
Posted By: howie ll
Date Posted: March 25, 2015 at 6:19 PM
You've wired it OK but you should have dioded across 85 and 86, 1N4004, band to 85.
That's called a quenching diode and not installing it may have fried your GWA wire.
Remove the relay and test it.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: oldspark
Date Posted: March 25, 2015 at 7:14 PM
I saw "band to 85" and panicked but I take it that the starter kill from alarm is GND switching (and never +ve with IGN off).
|