2009 Highlander w/ smart key info?
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=139004
Printed Date: April 29, 2024 at 9:49 AM
Topic: 2009 Highlander w/ smart key info?
Posted By: 2001eclipse
Subject: 2009 Highlander w/ smart key info?
Date Posted: May 22, 2015 at 9:38 PM
Has anyone installed a remote start in this car? Planning on installing a 4X10 with the MC501 and THTLC12 (or whatever the model # the t-harness is).
The Highlander is the smart key with can (no keyport)
TIA
Replies:
Posted By: tedmond
Date Posted: May 24, 2015 at 7:35 PM
ive done them before usng idatalink, never before with a 4x10. Should work just fine though. Make sure you do not have a factory remote start installed, or your install will become very interesting.
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: 2001eclipse
Date Posted: May 24, 2015 at 9:04 PM
Did the highlander you worked on have push to start withOUT keyport?
Im having trouble locating which ignition, starter, acc wires to use cause all the wires at the button are all thin...
Posted By: tedmond
Date Posted: May 24, 2015 at 11:35 PM
The MC501 is NOT required if you have a smart key hihglander. The Relay pack is only required for high current applications (not appliciable to you).
You need to follow type 2 install with the T-harness. The 4x10 will controls the push start button.
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: 2001eclipse
Date Posted: May 29, 2015 at 5:50 PM
Sweet thanks for the info bro, but Im still having a little trouble...
Do i have to connect any of these wires:
H2/2 Yellow/Black Data TX (Types 1, 4-6)
H2/3 ORANGE / Black Data RX (Types 1, 4-6)
H2/4 Tan HS CAN Low (Types 1-3)
H2/5 Tan/Black HS CAN High (Types 1-3)
Those wires I listed above along with a couple wires are coming from the T-harness.
I wish I had the car with me so I can post a pic, but once it comes later today, I'll snap some pics and post them tonight.
I also cant find the starter switch wire which the install guide says its at the main body ecu, and from what it looks like it says its above the fuse box area, but the only thing I found was so module for the power steering or something. Is there a starter switch wire I can grab from the push to start button? Is the starter switch wire a wire i can test as if it were a regular starter wire?
Posted By: tedmond
Date Posted: June 01, 2015 at 8:35 PM
You need these 2:
H2/4 Tan HS CAN Low (Types 1-3)
H2/5 Tan/Black HS CAN High (Types 1-3)
your vehicle follow install type 2a or 2b with the t-harness
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: 2001eclipse
Date Posted: June 03, 2015 at 1:06 AM
Any info on where I can get the starter switch wire?
According to the install manual its somewhere above/behind the fusebox, but all I can find is something that has to do with power steering. I couldnt even find the same looking plug.
Posted By: tedmond
Date Posted: June 05, 2015 at 7:01 AM
the body ecu is easy to find. look behind the fuse box and you will see a creme coloured housing. this is the ecu but encased. you should be able to find the correct plug by laying on your back-look upwards to the backside of the fusebox, and its the very top plug to the right
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: 2001eclipse
Date Posted: June 06, 2015 at 12:29 AM
Sweet, thanks for the info! I actually had to unbolt the ecu to take off the plug cause my first few attemps without removing the ecu got my finger cut from something lol.
Thanks again bro, your help/info is very much appreciated :)
|