535t install on 2010 ford taurus sel
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=139143
Printed Date: May 05, 2024 at 1:27 AM
Topic: 535t install on 2010 ford taurus sel
Posted By: xraytedrick
Subject: 535t install on 2010 ford taurus sel
Date Posted: June 29, 2015 at 9:53 PM
Hello. Does the 2010 Taurus have a control module for the power windows? Can the 535t be installed on just the drivers master switch or will wires need to be run to both doors.
-------------
Rick
Replies:
Posted By: howie ll
Date Posted: June 30, 2015 at 5:42 AM
Both doors to the motor wires.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: xraytedrick
Date Posted: June 30, 2015 at 12:54 PM
Hello. I've connected brown and white wires to drivers switch and green and blue wires to drivers motor. I tried programming and window will go down and inch then stop. Repeat that cycle and it stops. Tried programming multiple times with same result. What should I do next?
-------------
Rick
Posted By: howie ll
Date Posted: June 30, 2015 at 1:03 PM
Make surer you have correct motor wires in EACH door and read the instructions.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: xraytedrick
Date Posted: June 30, 2015 at 10:26 PM
Connected both sides straight to motor. Passenger side worked. Driver side only moved in steps never fully open or closed on learn routine. I tried helping the window up and down but that did not help. The instructions say additional programming may be an option but I tried placing it in learn mode many times. Is there a way to clear previous programming?
Is the window module part of the motor? Driver window motor harness has five wires and passenger has only two. I have motor wires hooked directly to proper up down on motor harness. Is there something else?
-------------
Rick
Posted By: howie ll
Date Posted: July 01, 2015 at 6:25 AM
You need to get inside the motor, good luck with that.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: xraytedrick
Date Posted: July 01, 2015 at 8:19 AM
Will it work wired as four window up only? Would 529t work in front driver door instead?
Thanks for your help.
-------------
Rick
Posted By: howie ll
Date Posted: July 01, 2015 at 9:15 AM
I thought the driver's door was what you were talking about.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: xraytedrick
Date Posted: July 01, 2015 at 9:53 AM
I wanted to install the 535t to control both front windows in both directions. It seems like I can't do that with the driver window module being part of the motor.
1. Will a 529t controlling that door only still have the same problem.
2. Can I use the 535t to only roll up all four windows or does the module in the driver door prevent that also?
3. Can I not connect the driver door wires and use the 535t to control the other three windows as auto up when armed? Will it learn only three windows (without driver window).
Thanks
-------------
Rick
|