Alarm install for 2010 Ram 1500

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=141836
Printed Date: May 04, 2024 at 1:18 PM

Topic: Alarm install for 2010 Ram 1500

Posted By: the12volt00
Subject: Alarm install for 2010 Ram 1500
Date Posted: October 08, 2016 at 12:14 PM

Hello everyone,
I would like to install this alarm/keyless to a 2010 Ram 1500 Automatic.

I have installed many alarms before with imported cars.

I wonder if with this car, do I need to buy anything extra ?

See, I don't have this in my toolbox:
ADS-RNG-GM3 iDatalink OEM Integration Can Bus Module

Here is the parts I have:

picture upload sites

Replies:

Posted By: lurch228
Date Posted: October 09, 2016 at 2:34 AM

Resistors for hardwire of door lock control 1/4 watt 330ohm, 100ohm and for (-)parking lights 1000ohm. Otherwise if you have the factory alarm use a DLPK convenience bypass interface module to do the door lock control and alarm control. As OEM alarm requires either OEM FOB or Transponder key in cylinder with ignition to dis-arm.

The DLPK does:

Core Functions
•Door Entry Monitoring
•Door Lock / Unlock Control
•Factory Security Control
•Hood / Trunk Pin Entry Monitoring
•Tach / RPM Output

Detailed Function List

W2W
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
RS-RAP Shut Down (Retained ACC Power)
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Hood Pin

D2D
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
RS-RAP Shut Down (Retained ACC Power)
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Driver Door Pin
SS-Entry Monitoring Hood Pin

Posted By: the12volt00
Date Posted: October 09, 2016 at 10:04 AM

Thank you. I have 2 related questions

1) Is there a wire to cut to completely forget about the Factory alarm ? Owner didn't tell me if car has Fact alarm.

Result: My Alarm/Keyless replaces the Fact alarm.

2) Can I use this ?
https://www./itm/Directed-29402-Dem-Universal-Alarm-Bypass-Module-Very-Good-/400996097451?hash=item5d5d3addab:g:6AEAAOSwHxVW7A3x&vxp=mtr

3) In case the car has no Fact Alarm (likely), are these 3 resistors really necessary ?
"Resistors for hardwire of door lock control 1/4 watt 330ohm, 100ohm and for (-)parking lights 1000ohm"

I have installed a few Third Party Alarm/Keyless and never did I need to order resistors. That the job of the alarm controller.

Posted By: the12volt00
Date Posted: October 09, 2016 at 10:06 AM

Sorry for the missing link: Please Remove **

www.e**b**a**y.c**o**m/itm/Directed-29402-Dem-Universal-Alarm-Bypass-Module-Very-Good-/400996097451?hash=item5d5d3addab:g:6AEAAOSwHxVW7A3x&vxp=mtr

Posted By: lurch228
Date Posted: October 09, 2016 at 5:43 PM

1)No as the Programming wont allow it to be disabled without the TIPM being reflashed.

2)No it is on compatiable with a 2006 RAM.
Manual for 20402 & 29402: https://www.readyremote.com/pdf/manuals/20402.pdf

3)MUX is part of vehicle and exists with or with out factory alarm.
Only if you use a bypass will you not need the resistors with or with out a factory alarm.