What Voice Module is this? how to install
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=33746
Printed Date: May 19, 2024 at 4:27 PM
Topic: What Voice Module is this? how to install
Posted By: blindxp
Subject: What Voice Module is this? how to install
Date Posted: June 12, 2004 at 2:40 PM
Trying to find install guide!? for this item (it might be DEI @ www.directed.com): https://www.kniepkamp.net/ebay/may04/CIMG0481.JPG I bought a viper 600 with poximity sensor and voice module. The prox. sensor is wired into the voice module already and has every wire hooked up to something (no loose ends). However the voice module has green, blue, yellow, orange, red, and black all left hangin :( I would guess red needs constant power, black is grounded to chassis and orange goes to the viper's orange wire (alarmed (-) output). Where do I put the rest? the blue still has a piece of solid black (for the speaker maybe?) The green still has apiece of black with a white stripe, the yellow has a crimp but no wire on the other end. Anyone know what goes where? grn, blu, ylw, org, red, bk all need somewhere to go!
Replies:
Posted By: jfk51502003
Date Posted: June 12, 2004 at 2:48 PM
WELL IN MOST CASES YELLOW IS CONSTANT...RED IS SWITCHED...BLACK IS GROUND...PASS THAT IT IS UP IN AIR...
Posted By: blindxp
Date Posted: June 12, 2004 at 3:01 PM
ok my old alarm had a switched 12v accessory output, I could put red to that....
Posted By: zargon
Date Posted: June 12, 2004 at 4:25 PM
when you connect the orange wire to the orange wire of the viper alarm youu will have to cut the wire from the alarm and place a diod in line with the stripe faceing twords the brainand the connect the wire from the voice mod and connect it on the brain side of the diod.
-------------
zargon ruler of estranorth
Posted By: blindxp
Date Posted: June 12, 2004 at 4:32 PM
copy and paste the image link to see it. I can't get to it by jsut clicking, go figure...
Posted By: blindxp
Date Posted: June 12, 2004 at 4:34 PM
"connect the wire from the voice mod and connect it on the brain side of the diod.
" what? connect my voice mod to the brain side of the diode? then the brain connects to the voice mod side? why wouldn't I just put the stripe of the diode on the other side? repeat?
Posted By: CutDog504
Date Posted: June 13, 2004 at 3:21 PM
What model voice module is this?? Is it a 516u? A 516l? or what???
Posted By: blindxp
Date Posted: June 14, 2004 at 12:53 AM
I don't know what make/model it is! And its ticking me off!
Posted By: Ravendarat
Date Posted: June 14, 2004 at 1:40 AM
Green and Blue are probally your triggers, yellow ignition, Red Constant, Black ground, Orange ?. On alarms and alarm sensors yellow is almost always ignition and red is Constant. Opposite of decks.
-------------
double-secret reverse-osmosis speaker-cone-induced high-level interference distortion, Its a killer
Posted By: CutDog504
Date Posted: June 14, 2004 at 2:53 AM
If its a DEI voice module, it will have a number on the brain. The number will most likely be 516U or 516L or sumthin like that.
Posted By: blindxp
Date Posted: June 15, 2004 at 10:05 PM
well I couldn't see a single marking on it, so any other ideas?
Posted By: blindxp
Date Posted: June 19, 2004 at 12:09 PM
bump
|