1997 sunfire power lock problem
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=38583
Printed Date: May 28, 2024 at 1:49 PM
Topic: 1997 sunfire power lock problem
Posted By: pimp2k4
Subject: 1997 sunfire power lock problem
Date Posted: September 04, 2004 at 2:09 PM
hi, i am installing the new compustar 2wss-as alarm/remote start. i have everything else hooked up but i cant seem to get the power locks to work. i am connecting the light blue and the white wires in the drivers kick panel, but i get nothing?? ne help would be appreciated Thanks
Replies:
Posted By: draasch
Date Posted: September 04, 2004 at 3:20 PM
Power Lock L BLUE DRIVER KICK (W/O OEM KEYLESS) ** #203
Power Unlock WHITE PANEL (W/OEM KEYLESS) #202
** Without OEM Keyless Door Lock Wires MUST Be Tested From PASSENGER Switch!! W/O OEM Keyless See Note #203 Reversal Rest At Ground Door Lock Diagram. With OEM Keyless See Note #202 Positive Pulse Door Lock Diagram.
how are you hooking them up from the alarm???? ------------- Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt
Posted By: pimp2k4
Date Posted: September 04, 2004 at 4:05 PM
ok, well i had an dei pager alarm before and all i did was run a wire from the passenger side over to the driver side, then hook them up the alarm lock and unlock outputs. this alarms lock/unlock outputs are + and -, so maybe im missing something, i dunno. so i just put both locks togther and both unlocks together, then put them on the appropiate wire from the alarm, but i get nothing...
Posted By: draasch
Date Posted: September 04, 2004 at 5:08 PM
what are the outputs coming from the alarm???? ------------- Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt
Posted By: pimp2k4
Date Posted: September 04, 2004 at 11:37 PM
the outputs are a blue wire that is positive lock, but doubles as a negative lock and blue/black wire that is negative lock, but doubles as a positive unlock.
Posted By: pimp2k4
Date Posted: September 05, 2004 at 11:14 AM
also there my car has keyless entry
Posted By: Velocity Motors
Date Posted: September 05, 2004 at 11:47 AM
You may need to boost the signal for the doors locks to work. If you are using the (+) output from the CPU use this diagram: Positive to Positive Relay Diagram------------- Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: pimp2k4
Date Posted: September 06, 2004 at 2:29 AM
what about the negative side for the unlock, same way??
Posted By: pimp2k4
Date Posted: September 06, 2004 at 2:29 AM
what about the negative side for the unlock, same way??
Posted By: draasch
Date Posted: September 06, 2004 at 4:05 AM
yes if you use a relay for lock, you will need one for unlock as well..your output is - and you need ot change it to +..... ------------- Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt
Posted By: pimp2k4
Date Posted: September 06, 2004 at 1:02 PM
is there a diagram that shows how the hook ups should be for me to do this? thanks
Posted By: pimp2k4
Date Posted: September 06, 2004 at 1:34 PM
ive read in other posts that if the car has keyless it uses a positive pluse lock system. Will that affect how i wire up the locks to the relay?? or is the diagram in this post what i need, just to boost the signal to the lock/unlock wires. Like i said before the lock/unlock wires from the alarm double as both positive and negative.....could it be that the alarm isnt sending enough current to unlock/lock the doors??
Posted By: Velocity Motors
Date Posted: September 06, 2004 at 1:44 PM
No it will not affect the way the relays are integrated into the system. All your doing with the relays is boosting the (+) signal from the alarm system to activate the OEM door lock/unlock system. You are correct about the signal not being strong enough that is what the relays will help with.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: pimp2k4
Date Posted: September 06, 2004 at 11:11 PM
thanks for all your help...im going to try tomorrow, ill let u know how it goes...thanks
Posted By: pimp2k4
Date Posted: September 07, 2004 at 5:52 PM
everything is working perfectly...thanks for your all your help Kevin
Posted By: Velocity Motors
Date Posted: September 07, 2004 at 11:46 PM
No problemo
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
|