Print Page | Close Window

Factory disarm on 02 Rav4

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=40404
Printed Date: March 28, 2024 at 5:12 AM


Topic: Factory disarm on 02 Rav4

Posted By: pvancorenland
Subject: Factory disarm on 02 Rav4
Date Posted: October 06, 2004 at 4:00 PM

I'm trying to install a remote starter on my '02 Toyota Rav4.

The car has a dealer installed "Securikey+ alarm"

I'm trying to locate the wire to disarm the alarm. Up till now I've only found a wire on my alarms main module "for use with remote starter kit".

Should I hook the FASD from my starter to this wire or is there another connection?




Replies:

Posted By: mxxmikexx
Date Posted: October 06, 2004 at 5:48 PM
dei doesnt even list a disarm wire for your vehicle
audiovox says it disarms with unlock , which normally means it isnt neccessary to disarm before remote starting. so before you beat yourself up looking for this wire, first try it without any disarm wire and see what happens. (when you bench the remote start, just leave yourself provisions for a disarm wire if needed)




Posted By: pvancorenland
Date Posted: October 06, 2004 at 6:53 PM

MxxMikexx,

Thanks for your reply.

The tech at bulldogsecurity told me that the disarm connection would be on pin 13 of the 14 pin connector in my kick panel, but I guess that is for a factory alarm. Mine is a dealer installed alarm. I only know it is a "Securikey+" alarm, but can't seem to find any info about it.





Posted By: mo12v
Date Posted: October 06, 2004 at 7:14 PM

<<<<<The car has a dealer installed "Securikey+ alarm">>>>>

If the Dealer Installed this Alarm............The Alarm probably Dis-Arms only with the Remote or Key / Valet.

I don't know of many DEALER Installed Alarms that will have Dis-Arm wire, Unless from Factory



-------------
MO

Don't Learn from Others Mistakes
You Might Be the One That Knows.




Posted By: pvancorenland
Date Posted: October 07, 2004 at 2:36 PM

> audiovox says it disarms with unlock

Do you have more information from audiovox?

Thanks





Posted By: audiopro111
Date Posted: October 08, 2004 at 1:39 AM
rav 4 does not come or offer a factory alarm unless if it was installed with an aftermarket alarm, there are two type of security systems that are usually installed in this vehicle the type that works with u'r factory keyless entry or the kind that comes with another remote other than the factory keyless also that securikeyis just basiclly a traking code almost like a window etching so i know this vehicle doesn't come with a transponder type key ,i've been working on rav 4's since they came out and i haven't seen or even heard of it ever offering a chipped key and you have to disarm anything but u may have to bypass the shock sensor to avoid falsing while remote starting,maybe the ign.wire too depending on the remote start u'r using

-------------
AudioPro111




Posted By: audiopro111
Date Posted: October 08, 2004 at 1:43 AM
if your remote start offer 2 wires that pulse a ground before and after starting you can hook up pulse before start to unlock and pulse after start to lock if it makes you feel any better but truthfully u don't need it....

-------------
AudioPro111




Posted By: pvancorenland
Date Posted: October 08, 2004 at 11:46 AM

audiopro111,

Thanks for your help.

I seem to have a dealer installed "securikey" alarm, made by Audiovox.

Audiovox advises to switch the "ignition" input to my alarm with my remote starter such that I have a 0 on the ignition input while starting, such that I can still use my original remote to open the doors (a 12V at the ignition input will prevent my original keyless to open the doors).

What I want to do is to use my new remote (from the starter) to open/close my doors and arm/disarm my alarm.

Right now, when I remote open my doors (using the door lock/unlock wires in the harness), my alarm won't disarm.

Is there any way (by wire) to arm/disarm my alarm (without using the valet switch)?

I managed to get a pinout of my alarm and it had a "disarm" input which is not connected in my car. Do you know anything about that?

Thanks,





Posted By: audiopro111
Date Posted: October 09, 2004 at 10:43 PM

SORRY i didn't respond earlier but the factor that your alarm is audiovox is cool because thats all i deal with,when you got your alarm did they give u an owners manual because if they did, on the top right of the front page it should say what model alarm u have;it may say PRO-9232a,PRO9232s,PRO9842a,PRO9842b,PRO9642ch, if any of these models match let me know and i'll have the answer for you also if u don't have it just describe to me what the remote that arms &disarms your alarm looks like,colors,and amount of buttons and i most likely can identify it like that.

thanks, talk to ya soon     AudioPro111



-------------
AudioPro111




Posted By: pvancorenland
Date Posted: October 10, 2004 at 1:23 PM

Hi AudioPro111

Allthough AudioVox is the manufacturer of the alarm, it isn't branded "AudioVox" but Securikey.

I confirmed with the tech at AudioVox that they were the manufacturer, but he referred me to "Gulf States Toyota" who is the importer for my region.

At GST, they could only give me the troubleshooting manual with wiring information, but according to them, there is no way to (dis)arm the alarm.

The funny thing is that the alarm has a pin named "Disarm" which is not hooked up to my car.

I tried probing it, but couldn't disarm the system through it.

I want to be able to (un)lock and (dis)arm my car with both my original Securikey remote and my new remote starter remote, so I guess I am left with four options

a) buy a spare Securikey remote controller and hook up the arm/disarm signals of my remote starter to the key through 2 relays. I'd have to hide the key somewhere under my dash

b) Use the valet disarm to disarm the alram, this involves giving the alarm ECU an ignition signal (making it think there's a key in the lock) and closing the valet switch within 5 seconds.

The arming can be done by enabling the auto rearm function

c) install relays to bypass my shock sensor, door and hood triggers.

d) throw out the alarm and install a decent one

I'm leaning toward a) because it is the cleanest option, but also kinda cheesy

So, if you could tell me how the Audiovox alarms are disarmed, I could try that on mine and see if it works.

I downloaded all Audiovox installation manuals and the only thing they say about the remote starter disabling the alarm was to mess with the ignition signal fed to the alarm ignition input

Thanks for reading through and hopefully someone can help me

Peter





Posted By: audiopro111
Date Posted: October 10, 2004 at 7:02 PM
first thing first what type of remote start ar u installing., next is the the wire that says disarm red ,RED / blk/ or yellow/black and are the remotes that disarm your alarm the ones from your factory keyless entry if they

-------------
AudioPro111




Posted By: pvancorenland
Date Posted: October 10, 2004 at 9:50 PM

I'm installing a Bulldog Security Deluxe 500 system.

The wire is supposed to be pink/black according to the manual, but it is not connected in my car. It is connected inside of the brain though and it is documented in the troubleshooting guide,so I guess it might be connected in some cars.

The remotes that disarm my alarm are kind of kidney shaped with two black oval shaped buttons for lock and unlock and a third round green button which can be programmed.





Posted By: Bloms
Date Posted: October 25, 2004 at 5:34 PM

I've got a SecuriKey+ Programming and Troubleshooting manual if that will help.  It has the 24 pin connector and a description of what each one is/does.

I'll try uploading the document for your viewing pleasure.






Print Page | Close Window