remote start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=49489
Printed Date: June 03, 2024 at 3:56 PM
Topic: remote start
Posted By: c3d
Subject: remote start
Date Posted: February 06, 2005 at 3:58 PM
hey, I am installing a polarstart remote start in my 1988 toyota celica. Have a few questions. 1. They grey connection goes to the hood pin switch, then is the connection completed by the hood pin switch being grounded out to the frame? 2. There are many wired that Don't seem to be needed for my application, is this true? the wires are: 12-pin harness (none of them seem to apply to my application). Parking Light (+) 12V Battery (the second one) 5th auxilary output Any help would be appreciated
Replies:
Posted By: KarTuneMan
Date Posted: February 06, 2005 at 4:29 PM
On a remote start, you need to use all of the 12v. connections. They give voltage to the internals of the unit. The 12 volt parking light wire is for the light flash. You don't NEED to use it, but without it no light flash. The aux outputs....NOPE, unless your doing more than a "basic" job -------------
Posted By: c3d
Date Posted: February 06, 2005 at 5:26 PM
cool. since you work at a dealer, do you have access to the diagram i need? if so, can i get a copy? if not, oh well. And about the hood pin switch. Was what i said right?
Posted By: daniel2002p
Date Posted: February 07, 2005 at 8:08 AM
yup, when the grey wire sees a ground, it will not let the remote start take place. here is the diagram Remote Starter Wiring Colors and Notes | Function | | Vehicle Color | Location | Start: | | BLACK/ WHITE | IGNITION SWITCH HARNESS | Ignition #1: | | BLACK/ ORANGE | IGNITION SWITCH HARNESS | Ignition #2: | | BLACK / YELLOW | IGNITION SWITCH HARNESS | Ignition #3: | | N/A | | Accessory: | | BLUE/RED | IGNITION SWITCH HARNESS | Brake Light: | | GREEN/ RED (+) | AT SWITCH ABOVE BRAKE PEDAL | Tach Signal: | | BLACK | AT IGNITER OR DASH TACHOMETER | Parking Lights: | | GREEN | (+) AT FUSE BOX | Headlights: | | RED / BLU (LO) & RED / WHT | (HI) (+) AT HEADLIGHT SWITCH | Diesel Glow Plug: | | | | Clutch Bypass Wire: | | | | Notes: | | |
Alarm and Keyless Entry Wiring Colors and Notes | Function | | Vehicle Color | Location | Constant +12 Volts: | | BLACK/ RED OR WHITE | IGNITION SWITCH HARNESS | OEM Alarm Disarm: | | | | Dome Lights/Superv: | | RED / WHITE | (-) PLUG AT FUSE BOX | OEM Horn: | | GREEN/ BLUE (-) | STEERING COLUMN HARNESS | Power Lock: | | BLUE/BLACK | DRIVER'S KICK PANEL * | Power Unlock: | | BLUE | DRIVER'S KICK PANEL * | Trunk Release: | | | | Alarm Input Wire: | | RED / WHITE | (-) PLUG AT FUSE BOX |
------------- 2005 Toyota Corolla S
1.8L VVT-i I-4
Always double check your wires with a DMM!!!
Do Not Use A Test Light!!!
MECP Certified Installer!
Best Buy 665 - IN IT TO WIN IT! TEAM MOBLE!
Posted By: c3d
Date Posted: February 07, 2005 at 1:40 PM
you my savior buddy! thanks!
Posted By: c3d
Date Posted: February 07, 2005 at 8:07 PM
alright, i got the: HARNESS 1: 2 (12V) battery connections done. purple is connected to the starter output yellow wire is connected to the ignition output orange is connected to the accessory output green is not used. HARNESS 2: black is grounded purple is connected to the BLACK/ orange at the distributor grey is connected to the hood pin switch orange is connected to the brake switch yellow is connected to the parking light output So when I put the fuses in for the battery connections, it would flash twice, and the lights would too, so i know they work. but when i go to flash the hood pin switch, to enter programming mode, nothing happens. the hood is up. and i use the PAB button, i tried just hitting it once, nothing happens, or four 4 seconds-pause-then again once more. still nothing. If you have any advice, pleaase let me know! I leave for work tomorrow morning for 2 weeks, and i want to get this done before i leave. thanks.
Posted By: daniel2002p
Date Posted: February 07, 2005 at 10:19 PM
what kind of alarm is it by the way?
------------- 2005 Toyota Corolla S
1.8L VVT-i I-4
Always double check your wires with a DMM!!!
Do Not Use A Test Light!!!
MECP Certified Installer!
Best Buy 665 - IN IT TO WIN IT! TEAM MOBLE!
Posted By: daniel2002p
Date Posted: February 07, 2005 at 10:21 PM
also make sure that the BLACK/ white wire is grounded also, if it is not grounded, it will not let the remote start start the vehicle!!
------------- 2005 Toyota Corolla S
1.8L VVT-i I-4
Always double check your wires with a DMM!!!
Do Not Use A Test Light!!!
MECP Certified Installer!
Best Buy 665 - IN IT TO WIN IT! TEAM MOBLE!
Posted By: Ravendarat
Date Posted: February 07, 2005 at 11:39 PM
How do you know it has a BLACK/ white wire when he didnt state what kinda remote start is it? The DEI units have that wire but if he is flashing the hoodpin than it could be something made by a company like automobility in which case there is not BLACK/ white wire. So this brings up the previously asked question, What kinda Remote Start is it?
------------- double-secret reverse-osmosis speaker-cone-induced high-level interference distortion, Its a killer
Posted By: c3d
Date Posted: February 08, 2005 at 8:02 AM
its a polarstart ps-3125sh automatic transmission remote start.and its just a black wire. and it is grounded.
|