Hello Everyone.
I need a 2001 highlander wiring diagrams. Are they the same as the 02 model. Also need to know what size and kind the Diodes I need to voide the dome light delay for each door.The last this is the immobilizer system. Who make a good immobilizer system bypass.
I'm thing installing the Viper 791. I need to get all the help before I get start.
Thanks so much!!:)
For the immoblizer I would go with the DEI 556U. Very easy to install, nut remember for this you would have to give up a key. A 1N4002 or similar would do the trick for the diode. You can get these at your local radioshack.
TOYOTA
MODEL | YEAR(S) |
HIGHLANDER | 2001 - |
KEY | T-HARNESS | IMMOBILIZER |
TOYKEY-1 | N/A | N/A |
PART | COLOR | LOCATION | DIAGRAM |
12 VOLT CONSTANT | WHITE & BLUE / YELLOW (+) | IGNITION SWITCH HARNESS | |
STARTER | BLACK/ WHITE (+) | IGNITION SWITCH HARNESS | |
STARTER 2 | N/A | | |
IGNITION 1 | BLACK (+) | IGNITION SWITCH HARNESS | |
IGNITION 2 | BLACK / YELLOW (+) | IGNITION SWITCH HARNESS | |
IGNITION 3 | N/A | | |
ACCESSORY /HEATER BLOWER 1 | PINK (+) | IGNITION SWITCH HARNESS | |
ACCESSORY /HEATER BLOWER 2 | N/A | | |
KEYSENSE | N/A | | |
PARKING LIGHTS ( - ) | N/A | | |
PARKING LIGHTS ( + ) | GREEN (+) | @ HEADLIGHT SWITCH | |
POWER LOCK | BLUE/RED SEE NOTE * | SEE DIAGRAM | 29358_HIGHLANDER_TOYOTA and LEXUS door lock interface.pdf |
POWER UNLOCK | BLUE/WHITE & BLUE/BLACK SEE NOTE * | SEE DIAGRAM | |
DOOR TRIGGER | GREEN/ YELLOW (-) | DRIVER KICK PANEL | |
DOMELIGHT SUPERVISION | USE DOOR TRIGGER WIRE | | |
TRUNK RELEASE | N/A | | |
SLIDING POWER DOOR | N/A | | |
HORN | WHITE/ RED (-) | @ STEERING COLUMN | |
TACH | WHITE/ GREEN (-) | PIN 27 @ ECM SEE NOTES ** | |
WAIT TO START LIGHT | N/A | | |
BRAKE | GREEN (+) | @ SWITCH ABOVE BRAKE PEDAL | |
FACTORY ALARM DISARM | DISARMS WITH UNLOCK | | |
ANTI-THEFT | TRANSPONDER | | |
EXTRA INFORMATION |
* THIS VEHICLE REQUIRES A SPECIAL DOOR LOCK DIAGRAM AND EXTRA PARTS SEE DIAGRAM ** ECM (ENGINE CONTROL MODULE ) IS BEHIND THE GLOVE BOX IT IS THE MODULE TO THE LEFT. |
-------------
MECP certified (If it really means anything)
Jeremy
2001 Highlander-------------
Be careful whose advice you buy, but be patient with those who supply it.
Thanks for the reply.
I have few more question.
1. Do I need the a relay for the door lock and if i do. What kind the relay and where I can get it.
2. Where is domelight relay in the car(Do i need to add 1 in). Can I connect the Domelight supervison output to the relay and it what pin?
3. Where is the neutral safety switch. How can I connect those wires.
4. My car does not has the factory Alarm. That mean I don't have to connect the wire form the Viper for the factory rearm and disarm wire, right?
1. Here is the door lock diagram.
1070.pdf
2. Does not need to be connected.
Dome Supervision comes on with unlock.
3. Does not need to be connected.
4. Correct, if you don't have factory alarm then those wire are not needed. The factory rearm and disarm wire bascically is a set of wire that allows you to retain the intergrety of the factory system.
-------------
Be careful whose advice you buy, but be patient with those who supply it.